Question about Televison & Video

1 Answer

LCD display is blank. Player works, but no display.

Posted by on

  • rena_28 Oct 12, 2008

    I don't understand how my MP3 could've been banged around because I always kept it in a padded case. Unfortunately, I doubt this player can be taken apart without it completely coming apart. Thank you in advance for your help.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 173 Answers

Lcd need backlights that are plugs around lcd unit and one or more could be unplugged if got banged around.
need more info.

Posted on Oct 08, 2008

  • larry hanson
    larry hanson Oct 22, 2008

    mp3 now? what an audio player? lcd need a back to show. liquid crystal display... a micro-p. could be out that runs the lcd.... or a ribbon wire came loose but since no banging around i would have to tear it apart and start easy with checking voltages.



×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sanyo lcd projector has horizontal scrolling lines in its picture. Is this different than a lamp problem? Electrical? All else works fine. Thank you. Sanyo PLC-5600n lcd video projector. Not a tv.


This is caused by the processor and not by the lamp. As you might know, these projectors display colors by blanking out the light with lcd pixels. Most folks don't know that any display devices such as displays on cameras, laptop displays, etc. use an amazing amount of original technology that powered CRT TVs. (Yes, even vertical hold, although done electronically today, is there.) You'll just have to send this one in for service.

Feb 26, 2010 | Sanyo Televison & Video

2 Answers

S video displays, but Component video is intermittant


Shall we assume that the DVD is fine, before addressing the TV issues? Does it work with any other device or component? Seems that if your S Video is clean, then it's just a matter of refining whether your DVD is as well. Check that, and let us know.

Feb 12, 2008 | Hitachi 53FDX01B 53" Rear Projection...

1 Answer

New Proscan 40 goes to green screen when using HDMI cables


I have the same problem with a 40" Toshiba LCD, Component cables work fine with FIOS but not HMDI, goes in and out then blank. HDMI with DVD player works fine. Best buy reported this same problem from users with this toshiba lcd but no solution.

Dec 26, 2009 | Proscan PS50700 50" Rear Projection...

1 Answer

Tv cuts on for a few seconds and right back off on its own


We had a Sony LCD burn out and display the exact same behavior. You have to isolate if your cable box/pc is even involved or if it's a power supply/backlit bulb issue or similar.

The way you test a Sony is to disconnect ALL cables except the power, power the monitor up and hit the Menu button to display the test pattern (it's a small box with some color bars with NO SIGNAL on the bottom since there are no cables connected). After a few seconds, this test pattern would also go black even though the green light on the LCD was on. So it was the LCD itself that was blown and nothing to do with the PC.

I'd see if your LCD has some sort of test pattern or test mode you can access in the menu's with no cables hooked up to see if it can hold that pattern for more than a few seconds before going blank. If not, it would be indicative of a burned-out or blown LCD rather than the box that is supplying the signal.

Aug 20, 2009 | Mitsubishi WS-65613 65" Rear Projection...

1 Answer

Lcd dont tern on blank screen no light at all


Have you checked the fuse, as the led should still light if the fuse is good

May 05, 2009 | Televison & Video

1 Answer

Daytek dt 3220 will not power on


OK, your Daytek 3220 is not a projection TV, but an LCD TV.

Second, I hate to say it, but you bought a piece of junk. They have excellent pictures when they're new, but after a few years capacitors in the power supply go bad. When this happens, either the controls and remote stop working, or the TV starts blanking out, or it will just die and never work again.

The solution is to go buy a new TV. The power supplies are no longer available, and even if you could get one very often the faulty power supply has damaged the main board and/or the LCD panel.

In about 5% of these cases, replacing the capacitors will get the TV to work, in about 25% it will get the TV to work, but because the main board has been damaged the TV will intermittently blank out. In another 25% the LCD panel has been damaged so once repaired you will see dark streaky patches across the display.

In the rest of the units you could have all three problems or any combination of them.

It'ds really too bad because they use a Samsung panel, and have excellent pictures when they're working.

Jul 23, 2008 | Pioneer SD-643HD5 64" Rear Projection...

1 Answer

The LCD screen on my HP PSC 1600 all in one printer is blank. It first would display the messages as mirrored images, then it would only work if the screen was down, now it will not display anything at...


I hate to tell you this, but it sounds as though the device itself is bad. HP offers a standard (1) year warranty. If you're printer is not that old you can call them and get the printer replaced. Depending on the functionality you lose with the broken LCD display I would either continue to use the other working services or I would just purchase a new model.

Hope this helps.

MO

Jul 14, 2008 | Televison & Video

2 Answers

Sharp 32" LCD tv, screen going blank every few minutes.


Hide the remote from the set for awile and see if that magically "cures" this symptom....accordianman

Feb 27, 2008 | Televison & Video

1 Answer

Toshiba 32" LCD video doesn't work anymore


Lamp has gone out, sounds like...accordianman

Feb 27, 2008 | Televison & Video

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69845 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6393 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...