Where can I get a Owners Manual for a Sears Craftsman Professional Plunge Router Model Number 315.248700.Its about 20 years old and only been used once.Original price was approximately $500.00 back then.,
An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert whose answer got voted for 20 times.
An expert who has written 20 answers of more than 400 characters.
Re: Plunge router manual
I have had incredible success over the years calling Sears product Help Line-usually Parts -they have sent me numerous manuals for 20+ year old lawn mowers, rototillers, and snowblowers -their after-market service makes me consider purchasing new products from them ...but I enjoy buying through auctions.....and hunting for manuals when I need them :)
-contact them at 1-800-366-PART (1-800-366-7278) -they will be able to help or transfer you to the right place
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There isn't a serial number on the DVR? The next thing I would try would be to power it up. When it boots up it should show the product name. If you can't power up then unscrew the case and look inside. The circuit board should have a model number or something. I have never seen any electronics that didn't have something printed on the board.
When you find any numbers, search Google for them.
It should IF the Craftsman opener is also of the rolling code type. Some openers use rolling code technology and some do not. You need to cross reference the model number of the craftsman opener with the remote to see if they are compatible. You didn't give the opener model number here so there is no accurate way of telling. Most Sears openers over the past few years are rolling code type.
Depending on how old your Remote Control Smart 3 Function remote is determines on how to access the battery compartment. It will either have a small screw which needs to be loosened or if it doesn't have that, it will pop open when a very small, thin, flat blade screw driver is inserted in the side seam of the plastic housing. It's going to be tight, so be gentle with it. Once you access the wafer battery, note which side is up (+ or -). That's the way you want to install the new battery.
I had the same issue yesterday with my remotes which are model 850CB. I fixed it by following these steps on Chamberlain's help site:
1. Press & release the "learn" button on the motor unit.
2. Within 30 seconds, press and hold the button on the remote.
3. Release the remote button when the light bulb on the motor blinks. It has learned the code.
Use menu on DVR to assign internal IP and gateway and port number.
This Local IP must be in the same Gateway range as the Router. If you are unsure check the Router and locate the Status section, or goto the command prompt of your windows operating system and type in ipconfig.
Look for Gateway. If the Gateway is 192.168.1.1, then you can make the DVR's IP anything from 192.168.1.2 - 192.168.1.255.
Also you will need to use the same SubNet Mask, which is typically 255.255.255.0, and also use the same gateway.
Next find out what port your DVR uses. The easiest way to it is by reading the manual of your DVR. Look for the network section of it.
Also if it comes with network software, check out if in the connection area the software shows the port number.
Also check the Server software/Programming (Network section of it) to see if the port is listed.
In many cases it will be as simple as just Port 80, which is an HTTP port.
Set your router to forward chosen port to internal IP address of DVR.
To access the Router itself, use the Gateway you just located. If the gateway is 192.168.1.1, then enter that into the location edit box of your browser and then click the Enter button. A username and a password are typically required, but it depends on a router. For Linksys use "admin", "admin". By default DLink doesn't require any username or password (It is highly recommended to change the default password).
Once you're logged into the Router, in the Applications & Gaming Section / Servers of the Router, you need to add a Server/Application. Enter the port number and select TCP only. Where it says Port 0 to 0 enter the same port number twice. Or if your DVR uses for example, ports 3550, 4550, 5550, 6550, and there is nothing else utilizing these ports in between, then you can actually just enter one line, 3550 - 6550.
Enter the DVR/Cameras internal IP.
Originally Posted by Example
If the port was 1024, and the Local IP is 192.168.1.200, then it would be:
NAME = Anything you want Port = 1024 TO 1024 TCP/UDP = TCP LOCAL IP = 192.168.1.200 ENABLED = CHECKED
NAME = Anything you want Port = 3550 TO 6550 TCP/UDP = TCP LOCAL IP = 192.168.1.200 ENABLED = CHECKED
Set up additional entries for as many ports the DVR uses, to the same local IP. Check your DVR manual and it's networking section for all additional ports required. Also check the DVR software itself.
If your router has enough free entries, you can seperate them. Use it like DVR_HTTP for the browser port, DVR_AUDIO for the audio port, etc.
If you are going to use VNC to a PC DVR, then you would need to set up port 5900, and perhaps call it VNC_DVR, for example.
You have a static IP so you don't need to use sevices like www.dyndns.org . You just enter your static IP and your router forwards packets to your DVR.
Everything sounds ok. Try to add more port in your port forwarding. Actually, even if you don't forward port 80, by default its already open because that is for internet access. Research more port that your dvmre is using. You may want to isolate the problem by connecting your dvmre directly to the modem and check if it works there. If not, maybe your ISP is blocking some port the your dvmre is using.