Question about Panasonic PT-53WX52 53" Rear Projection Television

1 Answer

Panasonic pt53wx52f reply

Just wanna say thank u soooo much for all your help...im gonna send ya oics in a little bit,we did what you suggested and its a little better but still vertically off and so i cant match up colors up right

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 41 Answers

Ok no problem happy to help.

Posted on Oct 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PT53WX52F three blinking light


short protection: one of the several 2.2 ohm blue resistors in front of the convergence chips is burnt/discolored and bad.

Both chips would have to be replaced.

Do it yourself if you can solder and I have instructions for this repair.

photo of chip attached.

Let me know if you have questions.


3_5_2012_4_01_24_pm.jpg

Mar 04, 2012 | Panasonic Projection Televisions

1 Answer

Model PT53wx52f had a pop then the picture looks warped the colors are warped. Is there a way to fix this?


If you look here on the site under "tips" you will find I have posted start to finish and step by step instructions for this under "Panasonic do it yourself convergence" repairs.

If you have specific questions post a comment here and I will help--I have fixed hundreds of these sets--if you have some minimal skill you can do the whole repair for under 30 dollars parts cost(I can tell you where to get the parts).

SD TECH

Apr 13, 2011 | Panasonic Projection Televisions

2 Answers

My Panasonic PT53WX52F has a sideways hourglass picture with the green scroll running in an arc with the same red scroll running straight across. Is this the convergence chip you talk about?


There are two common problems with these sets.

Problem #1) Convergence

Symptoms:
  • Screen Looks 3D
  • Colors wont align
  • Video may look distorted
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Oct 23, 2009 | Panasonic PT-53WX52 53" Rear Projection...

2 Answers

Reset parental lock for panasonic pt-53wx53


Hi, try this it works' on most pan. tv`s, ON REMOTE push the power button for at least 7 seconds, video-tek

Feb 11, 2009 | Panasonic PT-53WX53 53" Rear Projection...

1 Answer

Service Manual for Panasonic PT53WX52F


<span class="postedby"><span style="font-weight: bold;"><span id="ctl00_ctl00_MainColumn_CenterColumn_ThreadBox1_lblAuthor" lang="6649">lonemountain,<br /><br />Did you receive the Service Manual? I'm in a similar position with convergence problems. If you did, would you send a copy to<br />vipnite at yahoo dot com<br /><br />I would greatly appreciate your help.<br />Kind Regards,<br />Ricky<br /></span></span><span id="ctl00_ctl00_MainColumn_CenterColumn_ThreadBox1_lblTime"> </span></span> <!-- from fixya rte -->

Dec 27, 2008 | Panasonic PT-53WX53 53" Rear Projection...

1 Answer

Panasonic pt53wx52f reply


No problem happy to help. This can get kind of complicated but I will try to walk you through it. Ok in your original post you said that you cleaned the lenses. There should be three of them these are the top of the tubes. One is the red one for blue and the green one is in the middle. they look like large cylinders. If I could see a picture of the unit when it is on it would be a lot easier. But the easiest way to get to the mechanical adjustment fort the tubes is through the front. Below the screen it should have a cloth front. This is a panel that is covering the tubes. remove this panel (there will be screws in the back and the panel should pop off.) This is the really tricky part below each tube there is a board that is attached to the tube. and above that board usually about three to six inches you should see three round circles with a kind of lip on each one these are the mechanical adjustments. Before you do anything to these we need to find the screen voltage adjustment box it is about 3inX3in usually black colored. and it will have six little knobs three on top and three on the bottom. These can be adjusted using a screw driver. One set of three will be labeled focus and the other screen. They should also have a label next to each knob saying the color B for blue G for green and R for red. It sounded like your green was off too much green maybe make small adjustment very small adjustments to the green focus and the green screen. Usually it is right for brighter left for dimmer if you adjust it to much the tube you are adjusting will go into overdrive and the whole tv will shut off. Adjust it until it looks better then depending on how it looks after you adjust the screen and focus will will have to play around with it it is a trail and error procedure. Then move on to the mechanical adjustment for the tubes the circle looking things. What i usually do is put it on a cross-hatch or some kind of picture that is stationary and has line s in it it makes it a lot easy than doing it on a moving picture. Use the title screen to a dvd movie or something like that. when you are looking at the tubes when the tv is on you will see the different colored tubes red, blue, and green once you have the green tube adjusted through the screen voltage box mentioned earlier to your liking then adjust the mechanical adjustments on the blue and red tubes use the lip on the circles to turn it left or right in small measures. you will see how each circle moves it in a different way. What you are trying to do is over lap the blue and red on top of the green. You will have to play around with this to find tune it it can be very difficult. Let me know if this helps if you still need help after you try this their is another route that could be used but it is hard to be absolutely sure without actually seeing the unit. Good luck

Oct 07, 2008 | Panasonic PT-53WX52 53" Rear Projection...

1 Answer

Resistors capacitors


do you have the schematic? your being told things that are unkown until you have the schematic in hand to confirm. call someone that is a tech!

May 10, 2008 | Panasonic PT-65WX51 65" Rear Projection...

2 Answers

IC module part for Hitachi 50EX12BA?


Hi.. look I am willing to obtain & send ya the "bit" free of charge if ya can find out what the "Bit" is ...lol I found a link below that indicates a free service manual to help with identifying the "Bit". www.eserviceinfo.com/downloadsm/11998/Hitachi_50EX12BA.html I "Googled" Hitachi 50EX12BA and got a lot of "Hits"... see if ya can get the part number and your return address and send it to my email zylab@xtra.co.nz, if i can obtain it I will send it on ASAP.. Anything for support.. alla best from New Zealand..

Aug 18, 2007 | Hitachi 50EX01B 50" Rear Projection...

Not finding what you are looking for?
Panasonic PT-53WX52 53" Rear Projection Television Logo

Related Topics:

443 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

The Knight
The Knight

Level 3 Expert

68368 Answers

Are you a Panasonic Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...