Question about Xact Communication Xact WristLinx X33X 2-Way Wristwatch Communicator with 38 Sub Codes: Ear Bud with Microphone 2-Way Radio

1 Answer

Cb microphone don't work correctly

I replaced my radio shack cb microphone with a cobra m77. Now the cb is on constant transmit. when I push the button I receive. It's just the opposit of what it should be. Can this be corrected?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 131 Answers

IF YOUR COMFORTABLE WITH TAKING THINGS APART & CAN USE A SOLDERING IRON.ITS JUST A MATTER OF REVERSING THE LEADS GOING TO YOUR MIKE KEY.OTHERWISE I WOULD SUGGEST TAKING IT BACK & GETTING ONE THAT IS COMPATABLE WITH YOUR RADIO.

Posted on Nov 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Do you leav the cobra micro talk walkie talkies on when charging


Also, never transmit with them in the charging cradle. I know, lots do but you risk ruining the radio beyond repair.

Dec 26, 2014 | Cobra LI6050-2WXEVP microTALK 22 Channel...

1 Answer

Constant static on my walkie talkie


Check the squelch level, either the knob or on the menu. When the squelch is 'open', there will be constant noise. If someone is transmitting nearby, do you hear them clearly? If not there may be a problem with the receiver in the radio.

Oct 01, 2014 | Cobra Two-Way Radios

1 Answer

Cobra microtalk


Try having a look at the manual on how to turn off VOX or change the sensitivity of the mic ok

Jun 27, 2014 | Two-Way Radios

1 Answer

When car is on the cb is on but wont show no reading or show my channels


check your PA/CB switch and your microphone connection, I don't know this specific radio, but these are the two primary items that can cause this issue on most cb radios.

Oct 16, 2013 | Cobra 19 Ultra Iiie 40channel Compact Cb...

1 Answer

I have a headphone/microphone that isnt cobra brand and fits into the cobra cxt175, but wont work. Will it work or do i need cobra brand?


Its probably wired different than Cobra like Microphones are. If you tamper with wires you may try combinations and it may work. Otherwise, best to buy Cobra replacement.

Mar 30, 2011 | Cobra Microtalk 100 FRS Walkie Talkie...

2 Answers

Constant RX mode on cobra microtalk PR3850WX


Sounds like the radio was subjected to electrostatic discharge. If you have your manual, and it describes a way to do a "master reset" on the radio, follow the instructions. This usually involves pushing down on one key while turning the radio on. Otherwise you have to find a licensed dealer for factory service, as there is no way to repair the radio yourself. The use of surface mount technology still confuses many Techs unless they have been to a company's two or three week seminars.

Jul 23, 2009 | Cobra Two-Way Radios

1 Answer

I have a Cobra 28 wx nw st and the two ceramic capacitors had cracked on the antenna connections inside. These look to be for the weather part. But i am having a hard time identifying these to replace...


4 pins
pin1 Ground (shield) and the red wire together
Pin 2 Audio white wire
Pin 3 Transmit blue wire
Pin 4 Receive Black receive

enjoy
CB Dave
Trenton Ontario

Jun 29, 2009 | Cobra 29WXNWST (40 Channels) 2-Way Radio

1 Answer

My cobra hh-36st cb radio is stuck in TX mode. The RX/TX light is red each time it is truned on. Removing and replacing the batteries has not worked.


G'day,
I think your problem with the Cobra cb is in the microphone, you should have a plug on the Mic cord end ,try disconnecting this from the CB unit and see if it clears it self. If this does the trick your problem is in the Mic it self, or the cord has a fault in it. However if you still have a problem it may be that the transmitt/ receive relay located in the Cb is stuck on transmitt, sometimes this can be cleared by tapping the case with the handle of a screw driver, place towel on the case first to stop any damage to the case( this doe's not always work) you may in this case need to have it serviced
all the best hope I have been of help,
John

Apr 08, 2009 | Cobra Two-Way Radios

1 Answer

Cobra 142 base


I don't know this radio individually, but heres the common thing that happens:
Sounds to me like the 8 volt regulator chip has blown after overvoltage. I expect the power supply has gone too, putting 18+ volts into the radio.
Repair the power supply. (Check its 13-13.8 Volts).
Then check the regulator (7808) is putting out anything, should be middle pin ground then 13V one side and 8V the other, if nothing, its blown. Replace it if gone.
Hopefully thats all thats gone and it should work again.

Dec 29, 2007 | Cobra PR-245/2 (7 Channels) 2-Way Radio

1 Answer

Maxon MCB 10 A


I'm not sure about your particular model but many CB radios use the microphone push-to-talk switch to kill the speaker while the radio is transmitting. If you don't have the correct microphone or if the cord has a broken wire it can cause the radio to have no sound. Another possibility is that the speaker is bad. There is probably an external speaker jack on the back of the radio. You could try plugging a different speaker or even an earphone in the jack to see if you get sound there.

Mar 07, 2007 | Maxon SP-100G (4 Channels) 2-Way Radio

Not finding what you are looking for?
Two-Way Radios Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xact Communication Two-Way Radios Experts

River bottom

Level 2 Expert

174 Answers

eradiostore
eradiostore

Level 3 Expert

1640 Answers

ka4iup
ka4iup

Level 3 Expert

3944 Answers

Are you a Xact Communication Two-Way Radio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...