Question about Printers & Copiers

1 Answer

Error F35 ON KONICA COPIER

WHEN I TURN ON THE COPIER IT SHOWS AN ERROR F35 - CAN I REPAIR WITHOUT CALLING IN SOMEONE ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Printers & C... Expert
  • 1,326 Answers

Yes you can, but need to know what model you have. different service mode for different models?

Posted on Oct 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

With me problem on konica minolta 7235 show error code f35-8


1. Turn OFF the SW2 (sub power).
2. While pressing the copy quantity setting button 2
and 5, turn ON the SW2 (sub power).
3. [Software DIP SW setting screen]
Select a DIP switch number.
Use the or key or numeric
keys.
To use numeric keys, press the DIP
switch number key at the left before
entering a DIP switch number.

select Dip 3 1 to 0 from 3 1 1

Mar 22, 2016 | Konica Minolta Printers & Copiers

1 Answer

Konica 7022 error F35-1


F 35-1 pertains to Abnormal Low fixing temp TH1. Try to clean the thermistor and reset the code by entering mode 25, software switch 3-1, make it zero. If the problem occur again, try to replace thermistor. Make sure that AC supply from mains is okay.

Aug 27, 2014 | Konica Minolta 7020 7022 7025 Copier Drum...

1 Answer

Konica error 35


Error F35 for Konica seems to be "low fuser temperature" error.
Could be a sensor or the fuser unit itself.
You should also try turning off the unit for about 10 minutes (unplug) and then restart it.

Apr 08, 2014 | Printers & Copiers

1 Answer

I have a Konica 7145. It has error code


This is a fixing unit over temperature fault. The device has detcted the fixing unit has gone over 470 degrees F.

You will need to check the Thermisters in the fixing unit, and repair or replace as needed.
Service mode DIP Switch needs to be reset after repairing.


WARNING
• When F34-∗∗, F35-∗∗ or F36-∗∗ (fixing temperature related abnormality) occurs, be sure to repair a defective part before setting the 25 DIPSW 3-1 to 0.
If the 25 DIPSW 3-1 is set to 0 without repairing a defective part, it may cause a fire.

Apr 26, 2010 | Canon imageRUNNER C3200 Copier

1 Answer

F35 error code


Warm-up was not completed
within a specified period from
the start of warm-up.
• The low fixing temperature
fault detection software is
activated.

The fixing temperature at the
end of warm-up is less than the
specified temperature.
• The low fixing temperature
fault detection software is
activated.


The fixing lamp does not turn
OFF within the specified period.



SOLUTION

Rewrite the data at
address “P47” in the
25 mode to “0”.

(1) Turn the main switch OFF.
(2) While pressing the numerical keys 2 and 5 of the copy
quantity setting button, turn the main switch ON. This
will enable the 25 Mode. The 25 Mode is used exclusively
to rewrite in memory and, therefore, does not
support normal copy operations.

Apr 21, 2009 | Konica Minolta Printers & Copiers

1 Answer

Pls. my Konica 1212


power supply went bad!
try this Reseat CN15 on CB than check the oporation of L1 L2
47 mode 00
hope that help

Oct 11, 2008 | Ricoh Aficio 1013F Copier

2 Answers

Error code f35


konica f 35 eror code

Aug 06, 2008 | Printers & Copiers

2 Answers

Konica 1015


While holding 2 and 5 turn on machine.Press 4 then 7 then p.Press 0 then p.Turn off then on ,this will reset copier if it does not have a fuser problem which is f35.

Aug 01, 2008 | Ricoh 6513 Copier

1 Answer

Error code f-35-8


Hi,

On most Konica copiers, an F35 error indicates:
1. low temperature of the fuser; and/or
2. open lamp; or
3. open thermo wire fuse; or
4. open thermistor; or
5. or anything heat related at start or warm up.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

May 19, 2008 | Printers & Copiers

1 Answer

Error code F35 on my konica 1212 photocopier


That's a fuser error condition...I'll have to get back to you because i have to check in my book to remember how to reset it...Thank you for your patient !

Mar 19, 2008 | Printers & Copiers

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts

kakima

Level 3 Expert

96467 Answers

old marine
old marine

Level 3 Expert

1463 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...