Question about Packard Bell PC Desktops

1 Answer

Unable to ENABLE IDE Devices - Packard Bell PC Desktops

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 334 Answers

In bios can u enable it in there

Posted on Oct 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Unable to make SATA dive as primary master .


Remove the IDE hard drive, and connect the SATA drive to SATA0 (zero) port. Install the OS on SATA drive. You may have to check BIOS. F2 on boot should get you there.

Oct 09, 2012 | Dell Precision PC Desktops

Tip

Turn Direct Memory Access (DMA) on or off You must be logged on as an...


Turn Direct Memory Access (DMA) on or off

You must be logged on as an administrator to perform these steps.
is usually turned on by default for devices such as CD or DVD drives that support DMA. However, you might need to turn on DMA manually if the device was improperly installed or if a system error occurred.
  1. Click to open Device Manager. If you are prompted for an administrator password or confirmation, type the password or provide confirmation.
  2. Double-click IDE ATA/ATAPI controllers.
  3. Under IDE ATA/ATAPI controllers, for each item that has the word Channel as part of its label, right-click the item, and then click Properties.
  4. Click the Advanced Settings tab. Under Device Properties, select or clear the Enable DMA check box, and then click OK.

on Dec 14, 2010 | PC Desktops

1 Answer

What settings in the bios with maxtor as slve and quantom fireball as master


There are no settings in the BIOS for setting up master ans slave drives.
The hard drives have jumpers for configuring master and Slave drives.
If your hard drives are IDE/PATA hard drives and you intend to install these drives on the same IDE cable then you can set the jumper on Quantum drive as Master and the Maxtor on Slave.
I suggest that you install the Quantum as master on the 1st IDE cable and the Maxtor as Master on the 2nd IDE cable for maximum data transfer rate between the two hard drived.
Any other devices that are connected to these IDE cables will need to be jumpered as Slave devices.

Mar 28, 2012 | Gateway PC Desktops

1 Answer

Unable to get message from computer to printer. Message always appears : "Does not recognize USB port " I have tried all ports. Printer works as I tested on another computer.


Hi,

Go to BIOS .For BIOS please press del or F2 button on your computer POST .After enter in the BIOS select on board devices or Integrated devices.select USB option and select AUTO option in Legacy USB devices if more than one USB Port then enable all USB port in BIOS.After that if printer not working then pls re-install the printer driver again.

Nov 16, 2009 | Compaq Presario S6000NX (DQ178A#ABA) PC...

1 Answer

How to install Redhat Linux 4.0 on Acer Power Series with SATA.


So did you try to install with and IDE dvd drive? Might be a BIOS issue, update bios or get a ide dvd drive somehow...

May 06, 2009 | Acer PC Desktops

1 Answer

My computer wont let me install OS


You have to reboot and tap F2 to go to BIOS select option to enable the Secondary controller and to detect the proper IDE Devices?

Also make sure the IDE cable is firmly attached and the you have pin 1 alligned properly at all 2 (or3) connectors. And if you have 2 IDE devices attached make sure one jumper ( in HD or CD ) is set to master and the other to slave.

If none of this works, try a known good CD rom drive that you can try and try switching with a known good cable.

Once the system recognize the CD ROM youre set to go !

Jan 04, 2009 | Dell Dimension 2400 PC Desktop

1 Answer

My new MB has only 1 IDE and i have 4 IDE devices to connect


You can connect two IDE devices on a single IDE cable

Nov 19, 2008 | PC Desktops

1 Answer

I just bought a refurbished netvista pent4 2.4g. from computer geeks. it has no O.S. or drivers


Dear Transtripper,

It shows that your IDE option is not enabled in the BIOS. So, enable the IDE Controller in your motherboard.

Thanks,

Sep 26, 2008 | IBM Netvista Intel Pentium 4 2.4GHz /...

1 Answer

On my sony laptop the Matshita UJDA730 DVD/CDRW cannot be found. Windows cannot find the hardware divice code 41?


Log in to your bios by pressing F2 or F10 (key for going in to bios may change look while you boot up) and see in your bios information DVD rom is detected (IDE devices) if not enable it from the bios then Windows will automatically detect it - if not try to replace the drive with a new one.

Jul 17, 2008 | Sony PC Desktops

1 Answer

Dell Precision 380


So the 80GB drive is an IDE drive, right?

Different manufacturer's have different BIOS' so I can't say with certainty what you'll see in yours, but on my ASUS motherboards I have a one of three settings:

PATA
SATA
PATA+SATA

When I run both IDE and SATA drives I need to use the third setting. I sounds like you're shutting off the PATA when you enable the SATA so there's no drive from which to boot.

If I misunderstand your problem please let me know.

Dec 22, 2007 | Dell Precision 380 P4 Dual Core 3 GHz...

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Packard Bell PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Are you a Packard Bell PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...