Question about PC Desktops

1 Answer

Number keys won't work - PC Desktops

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,913 Answers

Check your num lock key on right side of key bord
if it is on then u can type num with right side.

Posted on Oct 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

X809745 001


test the keyboard for regional , languages in control panel, and set up the keyboard languages.and try again.
However you can restore the computer use the "system restore" to the laste date that you know was working good. and fix it
You can enable the Hot KEYS, in BIOS setup .
God bless you

Jul 29, 2013 | PC Desktops

2 Answers

Help it won't work


restar the computer HOLD the key f2 or esc depend of computer go to the setup, and restore to factory setup. and try again.
However if the problem persist, open the case and take out the small battery measure the voltage 3Volts, if not replace,or take out by 30 seconds this clean all information corrupt and try again.
God bless you

Jun 16, 2013 | PC Desktops

1 Answer

Keys won't type letters or numbers. can't type in password to unlock e-machine 1603


NUMBER LOCK
You have press the NumLk key (number lock) and this changes the right hand keys to a number pad.
Press the NumLk key (also doubles as the ScrLk key to toggle the Number lock). it is near the F12 function key. When the NumLk has been enabled a LED light is turn on to indicate this function has been selected. Press the NumLk key again to turn off the Number Lock and Num Lock LED indicator.

Mar 29, 2013 | E-Machines eMachines Desktop PC

1 Answer

Casio cash register t2100 won't sign in with clerk key


You have to enter your PIN number then press CLK# button

Feb 25, 2013 | Casio Parts Cash Register PC Desktop

1 Answer

My monitor won't pick up the computer on startup it was working fine before


MUCH MORE sinister than that!

"Who knows what evil lurks in the hearts of men...................
~ The Shadow KNOWS ~..................."

Just kiddin'.

How about posting the model number, so I can give more exacting information, than writing a page filled with generic one-size-fits-all information?

The model number is on the back, next to the Windows product key; or up on the side of the computer tower.

Post back in a Comment.

Regards,
joecoolvette

Feb 17, 2013 | Acer PC Desktops

1 Answer

I think i used the wrong disc to install windows on my dell dimension 2400. its stuck on 16-bit mode and the resolution won't change from the 800x600? and i can't connect to the internet, but my...


Hi there, On your laptop that can get on the internet, go to www.dell.com/support and download drivers for your Network Card and your Video Card from that site. Make sure you put in the right model number (dimension 2400). Transfer them to a USB key, and move the USB key to your desktop. Install those drivers and everything work will again. You may need to install additional ones as you see other things not working (like audio). If you need more help, let me know. -Alex

Aug 13, 2011 | Dell Dimension 2400 PC Desktop

1 Answer

Vostro 1520- keyboard stuck on randomly repeating keys after small liquid spill.. no liquid inside, only a few drops on keys and it won't type right. Tried USB keyboard but it won't override the...


short of replacing the keyboard, there is not much you can do. If not killer expensive, then you could at your own risk put isopropal alcohol inside the tray - move around and then turn upside down. this will be easier on the electronics and may dissolve the liquid depending on what it is. If the viscocity is too high, then it wont work but worth a try.

Jun 14, 2011 | PC Desktops

1 Answer

I want to downgrade my desktop acer aspire x1800 vista to xp pro everytime i run set-up it always showing me an error could not proceed,.


Most like ly the hard drive has a Vista recovery partition. That partition has got to be deleted. You'll need to open a command prompt and follow the guide very carefully or irreperable damage could occur.

Here’s the trick to delete and remove the EISA recovery or diagnostic partition in Vista. Before proceeding with the deletion action, make sure that at least a set of Recovery Disc Media has been created. Else, you won’t be able to restore your computer to working and factory default condition when any problem on PC requires reinstallation.
  1. Open a command prompt as administrator.
  2. Run Diskpart application by typing Diskpart in the command prompt.
  3. In the “Diskpart” prompt, enter rescan command and press Enter key to re-scan all partitions, volumes and drives available.
  4. Then type in list disk and press Enter key to show all hard disk drive available.
  5. Select the disk that contains the partition you want to remove. Normally, with just 1 hard disk, it will be disk 0. So the command will be:
select disk 0
Finish by Enter key.
  1. Type list partition and press Enter key to show all available and created partition in the disk selected.
  2. Select the partition that wanted to be deleted by using the following command, followed by Enter key:
select partition x
where x is the number of the EISA based recovery partition to be removed and unlocked its space. Be careful with the number of this partition, as wrong number may get data wipes off.
  1. Finally, type in delete partition override and press Enter key.
Once the partition has been deleted, exit from Diskpart, and now users can use the much familiar and much easier Disk Management tool in Windows (diskmgmt.msc) to manipulate the freed unallocated partition. Users can create a new volume (partition) with this space, or simply merge it to existing partition by extending the size of the existing partition.

Oct 08, 2009 | PC Desktops

1 Answer

The alphabatic key are not performing the numaric keys are working on their place


you have toggled on your numeric keys.... take a look at your keyboard for NM likely printed on the side of one of the top keys .... hit function (fn) and the nm key once at the same time... that should shut off number lock and return your keyboard to normal

Apr 19, 2009 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...