Question about GE 25932 Cordless Phone

2 Answers

Cordless Phone When trying to make or receive calls, message appears: UNAVAILABLE. We have 3 handsets, and this happens only on 1.

Posted by on

  • tsconnolly Oct 28, 2008

    2 of 3 handsets say unavailable

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

All 3 phones need to be placed on the main charger just once to register

Posted on Dec 04, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When trying to make a call,messages appears unavailable on both hand sets that i have,i can not receive or send calls, but my land line does.

Posted on Oct 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My vtech dect 6.0 keeps saying unable to call try again


I had this happen suddenly on 2 out of 3 handsets with a DS6151 base and DS6101 handsets. Well, what happened is there was no dial tone on either of the 2 handsets on either of the 2 lines and a message appeared on the display "Unable to Call Try Again" after some delay, if Line1 or Line2 button was pressed.

Oddly, the 2 that did not work were the ones normally on "extension" chargers and the 1 that did work was the one on the base unit. That caused me to suspect the base unit .. which it still may have been but the solution was NOT. And, also odd, the handsets seemed to still be synched with the base unit in many respects.

Cycling the power on the base unit did nothing.
These are fairly new units and battery life is generally much longer in my experience.

The Solution:
- Remove the battery from the handset that doesn't work properly.
- Re-install the same battery.
Whatever was wrong, this reset it and the handsets started working again.
Easy fix.

Mar 18, 2012 | Vtech DECT 6.0 Digital Cordless Phone

4 Answers

I have a GE Cordless 5.8 gigahertz handset and digital answerer. I can see the red light flashing during an incoming call, but hear no dial tone and no ringing. I just replaced the battery. The handset...


Hi,

Did you pay the Bill ?

this seems as if it,s incoming calls only. Check the line with an alternative Phone. This will verify the lines good. And eliminate that One.
Also check if theres A Tone/Pulse setting.
This can also have adverse effects.
If this is on an adaptor fitting with internet access, try removing the adaptor, and plugging the phone direct into the Socket.
Or try the phone on a seperate or diferent Socket.

Hope This helps.

Mike @ compurepair.

Mar 05, 2008 | Phones

1 Answer

How do i copy a phone book for the Uniden DECT1560 cordless phone


Kathy,
This should do the trick!

Copying Phonebook Entries to Another Handset:
You can transfer one phonebook entry at a time or all phonebook entries at once.
1) With the phone in standby, press the address book icon.
2) To copy one entry, find the phonebook entry you want to copy, press Menu /Select , and then select Copy.
To copy all entries, press Menu /Select and then select Copy All.
3) Move the cursor to select the handset which you want to transfer the entries to and then press Menu /Select .
If you select Copy All, Are you sure? appears on the display screen. Move the cursor to select Yes, and then
press Menu /Select .
4) The phonebook entries will be transferred to the designated handset. During the copy process, the receiving handset shows Receiving and the ID of the sending handset.
5) When the transfer is completed, Done! appears on the handset.


Notes: • The handsets must be currently connected to the same base.
• If the handset you want to transfer to already has seventy entries in its phonebook, you will hear a beep and Not enough memory in receiving unit appears on the display.
• If the selected handset is out of range or data transfer is cancelled, Unavailable appears in the display, Phonebook listings will not be transferred.

Have Fun!!

Jul 07, 2010 | Uniden DECT15602 Cordless Phone

5 Answers

Panasonic DECT 6.0 always says "New Voicemail"


Try pressing and holding the MUTE (CLEAR) button until the handset beeps. Then clear all incoming calls.

Nov 23, 2009 | Panasonic KX-TG1033S Cordless Phone

1 Answer

I have a GE 25922 5.6GHz cordless phone. It has 3 receiver. 1 of the receiver all ways says unavailble and it does not ring or can't call out. Can you help me with phone? Thank you, Sai.


UNAVAILABLE Indicates the handset is out of range. Or an additional handset is in use. Or there has been a base power failure, in which case you must place all handsets on the main base cradle for 20 seconds to re-register.

Jan 07, 2009 | GE 25922 Cordless Phone

2 Answers

I cannot use my phones since Saturday. The phone message on hand


try to perform a soft reset.

Using:
menu/settings/ restore factory settings.

Dec 22, 2008 | Uniden Cordless Phone

1 Answer

Semi Dead Panasonic KX-TGA100N with ''C533'' displayed.


Panasonic KX-TG1050N Cordless Phone. Base handset (No. 1, KX-TGA100N) does not work, no keypad response or dial tone. Green indicator message light ON (should only work with the TG1000N base unit) all the time till battery runs down. Display shows message ?C533?. Can still send and receive calls on extension phones 2 and 3.

Nov 11, 2008 | Panasonic KX TG1000N Cordless Phone

2 Answers

TRU9480 Won't unregister - get "out of range" message. I have followed the instructions implicitly. Jerry


Same manual as lethean but Page 24 if the previously used Base is Unavailable and your phone shows "Deregistration" in the Menu.

Base Unavailable (Handset Only)
To clear the base registration data in the handset, please follow these steps:
Press and hold "Hang up"and [#] for more than 5 seconds. Select the BASE UNAVAILABLE submenu.
BASE UNAVAILABLE appears. Move the cursor to select YES, and then press the OK soft key.
ARE YOU SURE? appears. Move the cursor to select YES. Press the OK soft key.

Oct 24, 2008 | Uniden TRU9480 Cordless Telephone

6 Answers

Tru9466 base and tru9465-2 handset


Same manual as lethean provided on a similar post but Page 24 if the previously used Base is Unavailable and your phone shows "Deregistration" in the Menu.

Base Unavailable (Handset Only)
To clear the base registration data in the handset, please follow these steps:
Press and hold [] and [#] for more than 5 seconds. Select the BASE UNAVAILABLE submenu.
BASE UNAVAILABLE appears. Move the cursor to select YES, and then press the OK soft key.
ARE YOU SURE? appears. Move the cursor to select YES. Press the OK soft key.

Mar 10, 2008 | Uniden TCX905 Cordless Accessory Handset...

1 Answer

Uniden TRU9488 Phone


OU might need to deregister the hand set first by holding down the red end (hang up key) and keep it down while holding the # key. If deregister wont work use base unavailable and yes, you are sure twice.

List the handset numbers of those working handsets
Using a WORKING handset follow these directions
Resetting Handsets
If you want to register the handset to a different base or
replace a handset with another one, you must first clear the
registration information from the base and the handset.
1. Press and hold [ ] and [#] for
at least 5 seconds, until the
SYSTEM RESET menu
appears.
2. Select the DEREGISTER HS
submenu. WHICH HANDSET?
appears in the display.
3. Move the cursor to select the handset ID to be de-registered
from the list, and then press the OK soft key. DEREGISTER HS
appears. CHOSE A NUMBER THAT IS NOT ONE OF YOUR WORKING HANDSETS
4. Move the cursor to select YES, and then press the OK soft key.
When ARE YOU SURE? appears, select YES. You will hear a
confirmation tone.
PUT THE HANDSET IN THE BASE CHARGER AND IT SHOULD REGISTER

Hope This Helps - It worked for me

Jan 28, 2008 | Uniden TRU9488 Phone

Not finding what you are looking for?
GE 25932 Cordless Phone Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Phones Experts

kakima

Level 3 Expert

96372 Answers

Cindy Wells

Level 3 Expert

4753 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a GE Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...