Question about Epson Stylus CX6600 All-In-One InkJet Printer

1 Answer

Open ink cartridge holder

I have an Epson all in one photo printer and I need to know how to get the cartridge holder in the right place
Thank you C Stephens midkid@casco.net

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Epson Master
  • 4,338 Answers

Here are some T/S steps for your problem:

Press the open ink cartridge holder - fontx1.gif Color button and open the scanner unit. Follow the messages on the LCD panel to replace the empty cartridge. See :

http://files.support.epson.com/htmldocs/cx66__/cx66__rf/ink_4.htm#replacing%20an%20ink%20cartridge%20a


Running a printer operation check
If you are unable to determine the source of the problem, performing a printer operation check can help you determine whether the problem comes from the CX6600 or the computer.
To perform a printer operation check, follow these steps.
r_1.gif Disconnect the USB cable from your computer. Make sure that Letter-size paper is loaded in thopen ink cartridge holder - r_3.gif feeder. r_3.gif Press the fontp.gif Oopen ink cartridge holder - r_4.gifn to turn on the CX6600, and make sure the ! Error light is off. r_4.gif Press the Setup Mode button to entopen ink cartridge holder - fontl1.gifode. r_5.gif Press the A or the fontl1.gif/fontr1.gif Select button repeatedly until 3.Nozzle check appears on the LCD panel, then press the fontx1.gif Color button. The CX6600 starts printing. The CX6600 prints an operation check page that includes a nozzle check pattern.
Compare the quality of the printed test page with the sample shown below. If there are no print qopen ink cartridge holder - a830r_24.gifems, the CX6600 is fine and the problem probably lies with the printer software settings, the application settings, the interface cable (be sure to use a shielded cable), or the computer itself.
a830r_24.gif
If the test page does not print satisfactorily, there is a problem with the CX6600. For example, if bands appear in the check
Please remember to rate Techs who assist you for free :)
Joe

Posted on Oct 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have inserted new ink cartridges but printer is only printing in yellow and black. Do you have any ideas on how to fix this? Thanks


Hello stan check to see if the ink cartridge is properly placed on the cradle, OR you may need to clean the cartridge ink holder, it has dried ink on it. OR run the printer test.

Jan 17, 2011 | Epson Stylus photo C87 InkJet Printer

1 Answer

Epson stylus sx200 refuses to acknowledge black ink bought direct from epson


I believe the DX series and the SX use the same system

# Determine which ink cartridges are not recognised.
# With the ink cartridge holder in the ink cartridge replacement position, lift up the ink cartridge holder lid and take the cartridge or cartridges out.
# Check that the cartridge is a genuine Epson ink cartridge - look for the EPSON branding and T0xxx codes on the cartridge labels.
# Check that the cartridges are correct for your Epson product.
# Wipe the green Intellidge Chip on the cartridge that is not recognised.
# Check the chip contacts within the ink cartridge holder for any debris or dried ink and wipe with a lint-free cloth if necessary.
# Check that the plastic at the bottom of the cartridge has been pierced.
# Check that the cartridges are in the correct slots.
# Reinstall the cartridges into the ink cartridge holder in the correct order.
# Push the ink cartridge down firmly. It should click into place.
# Repeat this for any ink cartridges that were removed.
# Push the ink cartridge holder lid down. It should clip into place and be secure.
# Press the Stop button, this will return the ink cartridge holder to the right hand side of the unit.
# If the error light flashes after the print head returns to the home position, the ink cartridge may not be installed properly.
# If the red light is no longer displayed, but Status Monitor still reports a Non-Genuine Ink warning.
# If the red light is still on the printer, and Status Monitor indicates that an ink cartridge is not recognised, follow the steps below.
# If the problem remains, there may be a fault with the ink cartridge.

Dec 30, 2010 | Epson Office Equipment & Supplies

1 Answer

How to change ink on an epson stylus NX105 printer


Hi there,

Here is how you can change the cartridge for the Epson NX105.

1. Turn on your printer with the its support stand on the right.
2. Press the nx100_tx100_ug.1.93.5.jpg Stop button. The print head moves to the nx100_tx100_ug.1.93.6.jpg position to indicate which cartridge is low or expended. Then press the stop button again to move the cartridge back to the right side.
3. Squeeze the tab on the cartridge and lift the cartridge straight up to remove it.
4. Now, before opening the new cartridge package, shake it four or five times to redistribute the ink evenly. Then remove from package and be careful not to touch the green chip on the cartridge.
5.
Remove only the yellow tape or sticker on the cartridge.
6. Insert the new cartridge into the holder and push it down until it clicks into place.
7. Finally, , lift the scanner slightly, release its support, and lower the scanner.

That's it!

If you need illustration, please click HERE.

Please let me know if this helps you. Thank you for using FixYa.

Nov 22, 2010 | Epson Stylus NX105 All-In-One Printer

1 Answer

PLSE ADVISE ON EPSON SX200 CHANGING INK PROCEDURE


The ink cartridges are all separate so you press the cancel button (with no jobs pending) to bring the cartridge holder in to the right place open the holder remove the cartridge and then replace it, let the printer purge the cartridge then your good to go

there are only four cartridges anyway
Black, Magenta, Yellow and Cyan the procedure is the same if you are changing just one or all of them

Mar 29, 2010 | Epson Stylus Multifunction Inkjet Printer/...

2 Answers

How do i eject the ink carrier?


hi there,

  1. Look at the Epson printer's LCD screen to see the ink levels for each cartridge. If your cartridge is completely empty, simply press the "Color" button. If your cartridge has a low ink level, press "Setup". Hold down the button on the upper left side of your LCD screen until the words "Replace Ink" appears, then press the "Color" button.
  2. Wait until you see the words "Open the scanner" on the LCD screen. Then lift open the printer top by pulling up on the side grips next to the scanner unit. Make sure that the scanner lid remains closed. The ink cartridge holder should move to the far right of the printer.
  3. After the cartridges have completely stopped moving, pull the cover of the ink cartridge holder up and toward you. Press in the tab of the cartridge you need to replace. Lift the cartridge straight up to pull it out of the holder.
  4. Unwrap the replacement cartridge and insert it securely into the holder. Press straight down until the cartridge snaps into place.
  5. Close the cartridge holder cover and make sure it clicks into place. Close the scanner unit and wait while the printer charges the new replacement cartridge. Wait until the word "Charging" disappears from the LCD screen before using your printer.
Do not turn off your Epson printer while the "Charging" message is still on the LCD screen because this may cause your inks to not fully charge. Turn off your printer only if there has been no response for over five minutes.
Clean up any ink spills with soap and warm water.

Replacement ink cartridge: Black (T048120); Cyan (T048220); Magenta (T048320); Yellow (T048420); Light Cyan (T048520); or Light Magenta (T048620)

Hope this initial info/idea helps.

Let me know for further instructions.

Thanks

Apr 29, 2009 | Epson Stylus RX500 All-In-One InkJet...

2 Answers

Change ink cartridge on epson stylus SX200 -printing head moves from side to side but then parks to the R and I cannot get access to change the cartridges.........


The ink cartridges are all separate so you press the cancel button (with no jobs pending) to bring the cartridge holder in to the right place open the holder remove the cartridge and then replace it, let the printer purge the cartridge then your good to go

Mar 24, 2009 | Epson Stylus Photo R320 InkJet Printer

1 Answer

Help with Epson Stylus CX 6000


Hi Open the cover then switch on the printer and then off from the mains when the cartridges are in the middle. Hope this helps!

May 23, 2008 | Epson Stylus CX6000 All-In-One InkJet...

3 Answers

Epson stylus cx4200 all-in-one?


1. Make sure the printer is turned on.
2. Make sure the document cover is closed, then closed, then open the scanner.
(Do not open the scanner when the document cover is open).
3. Press and release the ink button. The 'On' and 'Ink' lights flash.
If one of the cartridges is low or empty the printer moves that cartridge to the 'ink out' mark. Go to step 4.
If no cartridges are low or empty the ink cartridge holder moves to the ink replacement position. Go to step 5.
4. Pree the 'ink' button again.
If more than one cartridge is empty or low the next cartridge moves to the 'ink out' mark.
Once the printer identifies all the empty or low ink cartridges the print head moves to the ink cartridge replacement position.
5. Open the cartridge cover, squeeze the tab at the back of the empty cartridge and lift it out.
6. Before you open the new cartridge package shake it four or five times and remove it from the package .
(Don't remove or tear the label on the cartridge otherwise ink will leak out) .
(Don't touch the green chip on the front of the ink cartridge - you could damage the cartridge).
7. Place the new ink cartridge into the cartridge holder and push it down till it clicks into place.
8. Replace any other cartridges that need replacing.
9. Close the ink cartridge cover and press it until it clicks into place.
10. Close the scanner.
11. Press the 'ink' button. The printer starts charging ink and the 'on' light starts flashing . This takes about a minute . When it's finished the 'on' light stops flashing and remains on and the 'ink' light goes out.

You'll see all the above, with helpful pictures, at

this Epson support page

Mar 19, 2008 | Epson Stylus CX4200 All-In-One InkJet...

1 Answer

Help with Epson Stylus CX 6000


I NEEED DRIVER OF INSTALATION OF IMPRESORA STYLUS CX 6000 PLIS MI MAIL IS marsa78_eva@yahoo.com.mx

Jan 14, 2008 | Epson Stylus CX6600 All-In-One InkJet...

Not finding what you are looking for?
Epson Stylus CX6600 All-In-One InkJet Printer Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18334 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...