When booting it display insert smart card

I am using verifone vx510 ,When I insert a card it is show Connection failed. What should I you?

open slat and re insert the sim card .also check your setting

Replace the toner: Always use the smart card provided with the new Print Cartridge when replacing the cartridge. The smart card contains the information necessary to reset the level of Toner. Replacing the cartridge without using the smart card may result in the consumable management system being inaccurate.

1. Insert the smart card provided with the new Print Cartridge into the smart card reader. A "Change Toner?" message will be displayed.
   
   
   
   
2. Press the [OK] button. An "Open Front Cover Replace Toner" message will be displayed.
3. Push on the left and right side of the Front Cover and simultaneously lower the cover.
   
   
   
   
   
   
4. Grasp the handle on the Print Cartridge, and then raise and remove the cartridge from the machine.
   
   
   
   
   
   
5. Unpack the new cartridge, and then insert the cartridge into the machine.
   
   
   
   
   
   
6. Close the Front Cover. A "Have You Changed the Toner?" message will be displayed.
   
   
   
   
7. Press the [OK] button. A "Please Wait" message will be displayed while the machine reads the smart card, and then a "New Toner Remove Card" message will be displayed.
8. Remove the smart card from the reader and dispose of the card as normal office waste.
   
   NOTE: If the smart card has been used with a previous installation of a Print Cartridge, a "Remove Card Already Used" message will be displayed. The smart card can only be used once. Make sure to use the card that came with the new cartridge.

verefone the terminal has a problem in the display shows bad rtc chip, as I can compose for it functioning properly again?

It has to test the RTC before it can do anything. If you turn of the computer while it is testing it, you risk damaging the RTC so you won't be able to ever boot up. It will only boot if the RTC test returns a non-corrupt RTC.

Pl switch the machine off and put 2-3 pounds of pressure with your palm on the keyboard closer to the spacebar.. this will fix it..
it is caused by the weakening of the adhesive of the wires below the keyboard.
Long term option - get the keyboard opened by the an professional and cleaned properly..and fixed back neatly...

Clear RTC RAM (CLRTC)

This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5-10 seconds, then move the cap back to pins 1-2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup to reenter data.

Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure!If the steps above do not help, remove the onboard battery and move the jumper again to clear the CMOS RTC RAM data. After clearing the CMDS, reinstall the battery.

You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the CPU Parameter Recall (C.P.R) feature. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values

Forget the non-sense.

1. Remove the battery
2. Open the RTC Battery compartment
3. unplug the RTC battery
4. Press the power button to dissipate stray voltage
5. Re-install RTC battery and cover
6. re-install main battery
7. Re-boot and enter set-up to change date time etc.
   

You have to insert the smart card all the way in on these phones. You can use a pen cap or something to push it all the way in there until it goes all the way in and click and stays there. Then it will not say " insert smart chip" anymore.

couldformattt it all redo the system once u get locs on the so hard to get out even windows password makes u redo it all if u forget