Question about Konica Minolta magicolor 5430 DL Laser Printer

Open Question

Magicolor 5430DL with fatal error 0060H

5430 DL Magicolot Konica Minolta comes up with fatal error 0060H and thats all. Does everybody knows anything about this code? Thanks for help!!!

Posted by on

5 Suggested Answers

SOURCE: Konica Minolta Magicolor 2300 DL - Fatal Error Code 0EH ????

I had the same problem one time, they told me to pull out all of the toner cartriges, power off, power on, power off, replace all cartridges and the problem went away.

Who knows why. If this doesn't work....

Call Konica Minolta tech support.

They were pretty helpful to me.

Dave

Posted on Jan 06, 2008

  • 214 Answers

SOURCE: konica minolta magicolor 5430 dl

try updating driver and maybe firmware

Posted on Jun 19, 2008

  • 214 Answers

SOURCE: Konica Magicolor 5430 DL Fatal Error Code: 0300H

0300H: Polygon Motor malfunction

try restart if not helping then there can be problem with ph unit or PWB-A board

Posted on Jun 19, 2008

  • 12 Answers

SOURCE: Fatal Error Code 16H

Hi, pretty sure its the transfer belt not able to turn, remove it and make sure there is nothing blocking it, maybe a paper jam

Posted on Aug 05, 2008

  • 1 Answer

SOURCE: Magicolor 5430dl, "No Toner Magenta" error

Hi this might work, have you tried to remove the toner and re-seat it??
If this doesnt work very carefully take the toner somewhere well ventelated preferablly outside and give it a good shake for about 15-20 seconds, this frees any clogged toner there may be.

Failing all of that you would want to try outting a new toner in and see what happens.

Posted on Mar 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

5C00 Error Code as well as yellow and green alternating lights


To fix this error is much easier than it looks. Unplug the printer power. Move the ink cartridge cradle to the left. Over to the right you will see a small pad about 1cm square. This pad and the area around should be covered with ink. Get a cloth and press down on this pad - it's not fixed so should come away with the cloth, otherwise use tweezers gently. Squeeze the pad several times between your thumb and forefinger while inside the microfibre cloth to remove ink build up. Then when not much ink comes out on the cloth, clean the area in the printer around the pad so that looks free from ink too. Then position the pad back in place, move the cradle back into position, plug in and switch on - should work fine now.

Jan 14, 2017 | Office Equipment & Supplies

1 Answer

Qu'est peut on faire si la machine ca,o, IR2318 donne erreur 0000007-0000


hello sorry but another time try to use the language which can easily be read and thats English back to the point the cause of that error is the rotation of the fixing film is detected.
The reading of the main thermistor is 100C or higher and, in addition, the fixing film sensor does not detect the rotation of the film for 6 sec or more while the fixing motor is driven try to check on that fuser film if the error persist change the fuser unit

Jan 13, 2017 | Office Equipment & Supplies

1 Answer

How do I correct error h5 on a Sharp printer AR-5620N?


Hello Sudhir,
The error code H5 means there was at least 5 pages in a row where the paper did not come out of the printer correctly (most likely paper jams. The following manual will direct you on the steps needed to clear the code, please note especially page #8-3
Service Manual SHARP AR 5618 5620 5623 SME

The following video should help also;

Jan 09, 2017 | Sharp Office Equipment & Supplies

1 Answer

Bizhub C250 using to much toner. Images are very dark. Ink can even be rubbed off pages. How do you adjust?


Check that the fuser is not in enevople mode. two green handle up not down. check the files

Oct 28, 2016 | Konica Minolta bizhub C250 All-In-One...

1 Answer

I need a schematic for a Katsuda JMC4s Paper Cutter from Japan?


unnamed-04obcoisu5nwernczsqka0kl-4-0_0.jpg
Hi
I had JMC III KATSUDA (SH290HOP-N) paper cutter and memory shown ERROR 2. Memory did not work. Please let me know if you have any idea to fix it. My email is
leonardprint@gmail.com

Thank you

Dec 29, 2014 | Office Equipment & Supplies

3 Answers

How do i solve an error e000-0000 canon ir 2202 please


Dear
Its related to the fixing temp. do the error clear on service mode. then check the fixing film assy. heater circuit contact points for corrosion. Replace it.
Thanks.

Dec 12, 2014 | Canon Office Equipment & Supplies

1 Answer

How to set two sided printing in konica minolta pagepro1390MF


It might be better to place this problem in the computer section.

Oct 17, 2013 | Office Equipment & Supplies

1 Answer

Hp laserjet m1522f error 5 turn off and on


Hi, Error 5 is a Scanner error. When turning the printer on, have the lid up so you can watch the scanner movement. Does it move smoothly? It should go through a warm up and you should be able to watch the scanner movement. If there is a problem with the scanner, there isn't a lot you could do except. The service manual says the scanner assembly should be replaced. If it was my printer, I would try to take a closer look at the scanner assembly and check to see if the scanner unit is bound up somewhere, or maybe a drop of 3 in 1 oil on the scanner rails. Let us know what happens.
thanks

Oct 02, 2013 | Office Equipment & Supplies

1 Answer

Error code 3501


HI
I HAVE KONICA C6500
ERROR CODE 3501 and 3802 but know the error 3501
I know it rech high temperature I change the sensor 1 UP fuser roller
and I reset the error, the machine start and stop again with error 3501

Oct 01, 2013 | Konica Minolta Bizhub C 6500 Copier

1 Answer

Mfc-j630w error messagfe 4f


I don't know but I can't enter into maintenence mode I pressed just as its said but it's won't go and I really need my printer??

Jul 15, 2012 | Brother Multi-Function Center MFC-3360c...

Not finding what you are looking for?
Konica Minolta magicolor 5430 DL Laser Printer Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

5729 Answers

David Burkhart
David Burkhart

Level 2 Expert

207 Answers

George Mclaughlin

Level 2 Expert

333 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...