Question about Pioneer HTD-510 System

1 Answer

Speakers won't work

Just moved to my new place. the system was working fine in my old place. when i reconnected the speakers only the fronts were working.placed all speakers in the fronts and they work. when going thru the sound modes some work some don't. the sub woofer does not come on at all. placed all speakers where they belong. help!!!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I have had this unit for a long time when I started to experience channel drop out then no sound at all. I removed the relays from the output boards (pcbs) and replaced them. They are available through mouser, if you have any skill at desoldering/soldering should be no problem. The relays are sealed and could not be cleaned, replacement was the only option.

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The system WAS working fine. After I moved I installed the system again now the front speakers are not working. I'm sure it's not the cable or the speakers (if i connect in example: the left rear...


The system would have hung up. Please remove the power and leave the set aside for over 6 hours so that the processor will reset if there was any error that have crept into while it was powered . Also remove and reset all the speakers, if possible with an individual test on each- use a 1.5 V AA cell-.
The amplifer can also be reset if there is a note in your manual.

Oct 05, 2011 | JVC TH-A10 System

1 Answer

Front left speaker stopped working. I use the system with my computer (full volume on computer), and usually half volume on the speaker. I've had the speaker for a few months now. I looked the wiring to...


You 'looked' at the wiring but have proven it is defective by swapping the speaker independent of the wiring. What's next? Replace the bad wiring.

What happens when you put a working speaker and wire on the front left output?

Apr 14, 2011 | Samsung HTC550 Theater System

1 Answer

No Right Front Speaker Output


Swap speakers over...check the balance isn't fully to the other channel...swap left/right phono cables over (if thats how your using it) other than that i would say is broke.
Easy way to check speaker cable/speaker... touch a small battery (like used in a remote) across speaker wires, you will hear and see the speaker cone move.

Aug 07, 2009 | Audio Players & Recorders

1 Answer

Front bose speakers and bass module stopped puttimg put sound


If you're saying you hooked the Bose speakers directly to the Yamaha's amp instead of the prescribed way through their own bass module - they're cooked.

Dec 23, 2008 | Bose Lifestyle 12 System

3 Answers

No power


I have a TH-C30. I had the same problem where the unit just stopped working - no standby light and no recognition of power at all. After checking this forum and another, I opened the unit, found the ceramic fuse where the power comes in and went to Radio Shack. They have a T1AL250V fuse pack that is a 1 amp, 250 volt, 5 X 20 mm SLOW BLOW glass fuse which is a better fuse for this common problem. Their RS number is 270-1063 and a pack of 4 costs about $3. Put new fuse in and the problem was solved.

The repair took minutes - 3 screws on the back and two screws on each side. Lift the cover from the back (it is slip-hinged on the front) and replace the ceramic fuse. It slips out with a little help and the new one snaps in place.

Jul 21, 2007 | JVC TH-C30 System

2 Answers

RTD170 Speaker Problems


Have to change the set up in the menu section and make absolutely sure it is on surround dolby and not stereo. Check manual for set up.

Jan 01, 2007 | RCA RTD170 System

Not finding what you are looking for?
Pioneer HTD-510 System Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

John
John

Level 2 Expert

473 Answers

Dennis McCollum

Level 2 Expert

137 Answers

Are you a Pioneer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...