Question about Hotpoint 24 in. FDW60 Free-standing Dishwasher

2 Answers

Wont start wont let me change the cycle it flashes at 45degrees

Posted by on

  • five_angels Nov 12, 2008

    Same problem wont start wont let me change the cycle it flashes at 45degrees. I have cleaned .. poured water .. ckecked pipes . Still no joy ..

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My dishwasher wont start two green flashing lights please help

Posted on Mar 31, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Poured a kettle of hot water down the drainage part tried 20 mins later and worked think it was a possible build up of grease

Posted on Oct 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MY BRAND NEW SAMSUNG DISHWASHER HAS POWER BUT WONT START THE WASH THE WASH CYCLE THE TWO CYCLE LIGHTS JUST KEEP BLINKING


What 2 cycle lights? Samsung dishwashers indicate problems and errors by making different lights light up and/or flash. We would need to know the model number too.

Oct 07, 2014 | Samsung DMR78AHS 6 Cycle Stainless...

1 Answer

Does my whirlpol du1145xtpb1 dishwasherr need to be reset


SERVICE DIAGNOSTICS CYCLE
To start the Service Diagnostics Cycle, press the
following keys, in order, in less than 6 seconds, while in standby(power on but unit off):
Heated Dry, Normal, Heated Dry, Normal
To Rapid advance one interval at a time, press the Start key, noting that
unlike Standard cycles, the Diagnostics Cycle automatically resumes
after door openings and does not require pressing Start to resume.

Once the diagnostic cycle has run and shut off, run a normal wash cycle, empty and with no detergent, to reset the control to factory "normal" operation. Make sure there's plenty of hot water.


Read more: http://forum.appliancepartspros.com/dishwasher-repair/261055-whirlpool-quiet-partner-ii-clean-light-flashing-have-reset-still-flashing.html#ixzz2UOcsE2Yg
http://forum.appliancepartspros.com

May 25, 2013 | Whirlpool 24 in. GU3200XTP Built-in...

1 Answer

I have a beko washing machinethe start button keeps flashing during a cycle and it wont go on to the next cycle


Make sure that the inlet flow is good, remove the inlet valve to check. Also check the door switch and then the connections of the program controller unit. If there is loose connections it can cause errors and halt the program. Also it can be related to the program controller unit if after resetting the above there is no change .

Sep 30, 2011 | Beko 24 in. D3421F Free-standing...

1 Answer

I have the Whirlpool Quiet Partner 1 the wash cycle starts and about 20 Min.'s into it the clean light starts flashing or the the start light, one or the other each time and it wont dry the dish's anymore...


If the clean light blinks 7 times thats you heating circuit. Test the heater with an ohm meeting to see if it has open. If so order the heater kit and it comes with the control board.

Jan 12, 2010 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Start light flashing wont start cycle, what does it mean


count the number of flashes- this indicates fault ie will flash 4 times stop, flash 4 times stop. To clear fault, hold start button for 3 secs. Try running another fast cycle- if fault reoccurs count flashes: Number of flashes:1=NTC fault, 2=Flood switch activated, 3=Heating fault, 4=drain fault, 6=water inlet fault, 7=flow meter fault, 8=water level fault

Aug 06, 2009 | Whirlpool Dishwashers

2 Answers

Kenmore Dishwasher - Flashing Lights - wont start


Is the clean light blinking 7 times? If so this means you have a problem with your heating element

Dec 03, 2008 | Kenmore 15899 Built-in Dishwasher

1 Answer

L63 Salt light is flashing


goes for short time and 2 ljghts flash the red salt light wont go on

May 16, 2008 | Ariston Technologies L63 Free-Standing...

1 Answer

GE Quiet Power II Dishwasher


My GE dishwasher will only flash the start button and when I try to change a cycle it flashes the regular cycle and beeps every ten seconds without starting. I have had success once turning off the breaker and it resets.

May 11, 2008 | Dishwashers

1 Answer

Wont start


The lights flash when the door is not shut all the way, or the sensor that detects that the door is shut is not sensing the door is shut. Try pushing in on the door while hitting the start button.

Feb 13, 2007 | Frigidaire 24 in. FDB1051RE Built-in...

Not finding what you are looking for?
Hotpoint 24 in. FDW60 Free-standing Dishwasher Logo

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

bosch5

Level 2 Expert

157 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...