Question about Onkyo Audio & Video Receivers

1 Answer

0nkyo 505 standby light is on , but no display

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 142 Answers

Your unit is most likely in protect mode because of shorted output transistors in one of your channels.
Needs a service technician. Good luck!

barneyluc

Posted on Oct 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Onkyo TX NR515 .. when in standby mode .. light is not coming on .. everything works fine .. i must have pressed something by mistake but cant work it out what ... on the display panel in standby mode...


If Zones are turned on or, if a mobile device connected to the Front Input is charging (MHL), the HYBRID STANDBY indicator won't light. See the TX NR515 owner's manual at http://filedepot.onkyousa.com/Files/own_manuals/TX-NR515_English.pdf for more info.

Feb 19, 2015 | Onkyo TX-NR515 AV Receiver

1 Answer

No power output or display.green standby light flashes.


Sounds like either a blown mainpower fuse or the thermal fuse for the power transformer. If the protect circuit was kicking in, the display would light up, but then turn off with a red blinking light. the green light with no display means the transformer is not getting power.

Dec 31, 2013 | Denon Avr-1610: 5.1 Ch A/V Home Theater...

1 Answer

Stand by


try the unplug method first, if will not come out of standby the issue most likely is a power supply problem in the receiver.

Oct 15, 2012 | Kenwood Vr-505 Stereo Receivers

1 Answer

How do i connect the sub woofer for kenwood-505


I inherited a Kenwood SW 505 Sub woofer. I don't know if it works I plug it in but no lights.

Oct 07, 2012 | Kenwood VR-505 Receiver

1 Answer

Receiver stays on stand by


Turning On and Standby
On the AV receiver, press the [ON/STANDBY] button.
On the remote controller, press the [RECEIVER] button, followed by the
[ON/STANDBY] button.
The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
To turn the AV receiver off, press the [ON/STANDBY] button, or press the remote
controller's [ON/STANDBY] button. The AV receiver will enter Standby mode.

If you have any trouble using the receiver, a simple reset could solve your problem.Note that resetting the AV receiver will delete your radio presets and custom settings.
To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [ON/STANDBY] button. "Clear" will appear on the display and the AV receiver will enter Standby mode.

tinualbinale_5.png
Hope you are satisfied with my solution.Your valuable feedback would be appreciated.Thanks for choosing Fixya.

TinuAlbinAlex

Jun 15, 2011 | Onkyo TX-SR307 A/V Receiver

2 Answers

My pioneer vsx 815 amplifier has a flashing blue standby light. Have tried resetting by pressing enter and advanced surround keys. All it does is flash a few other LEDs and then goes back to the flashing...


Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/Pioneer-VSX-815-K-Receivers-manual/id/385dj989/t/2/

"enter and advanced surround keys"? I don't see that documented as a special function in the manual.

BTW: other than the Flashing light, is there a malfunction?

Page 72 describes how it REALLY resets...

Resetting the main unit

Use this procedure to reset all the receiver's settings to the factory default. Use the front

panel controls to do this.


1 Switch the receiver into standby.


2 While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds.


3 When you see RESET? appear in the display, press ENTER .

OK? shows in the display.


4 Press SYSTEM SETUP to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default
settings.

Mar 04, 2011 | Pioneer VSX-815-K Receiver

1 Answer

After turning ON the power/standby switch, the unit(receiver) display comes ON (green light) then after approx.4-5 seconds the display goes OFF and the unit defaults back to the standby mode (red light). I...


Is the red light flashing at first?
The unit may be going into protect mode. Lets hope it has done the job and the receiver has protected itself from failure.
Protect mode can result from speaker wires touching each other or the Amps2_bing.gif metal case. Check that first.
It can also be caused by unstable ohm loads if too many speakers2_bing.gif are connected to any of the outputs especially zone 2.
If you can remove all speaker wires and turn the unit back on. If it stays on, turn the volume down on the main zone and zone 2 if connected. Then reconnect speaker wires.

Nov 16, 2009 | Denon AVR-485 Receiver

1 Answer

Onkyo tx-sr500; power goes out; standby light blinks


Remove all Wires form speakers
Power on
Push Video1 + StandBy /On
appears Clear on display

Dec 22, 2008 | Onkyo TX-SR501 Receiver

1 Answer

Power works but receiver will not stay on


The outputs are blown and will require repair.

Dec 17, 2007 | Onkyo TX-DS575 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio & Video Receivers Experts

D. E. Hev

Level 3 Expert

1059 Answers

gbob59

Level 3 Expert

2963 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Are you an Onkyo Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...