Question about StarTech.com StarView SV211K 2-port KVM Switch

1 Answer

Cable boxes Hi I bought a starview3 super box and when i went and installed the channels most of them didnt work the epg is there but the station isnt im connected to ntl cable in Ireland i have a deambox500-c for a while now and it works perfect I tryed to reset factory settings and tune them in again but still the same can any body help me please I really dont know what im doing at all .

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 54 Answers

Subject: Star View 3 The Box Super when channels discappear ;o)
Hiya this is what I did & hopefully it'll work for U too, not too sure about Irish Ntl tho but worth giving it a go :- 1) Deleted all th channels & reset 'factory settings' by entering the code 0000, turned th box off waited a couple of minutes & turned it back on !!! 2) You may have to redownload channels so reconnect yr box to the computer & follow the link below (But try without doing this & goto stage 3) first & please let me kno if that works :- http://www.4shared.com/file/76886028/fd4ac296/GTRom_the_box_Super_8102e_081129.html?err=no-sess ) & press download !!! 3) ReConnect & Turn box back on; goto menu & press 1570 to get into the CASS SYSTEM & turn EMU on Reinstall channels & voila

Posted on Jun 23, 2009

  • 1 more comment 
  • Stace Godsell Jun 24, 2009


    Hiya this is what I did & hopefully it'll work for U too -

    1) Deleted all th channels & reset 'factory settings' by entering the code 0000, turned th box off waited a couple of minutes & turned it back on !!!

    2) You may have to redownload channels so reconnect yr box to the computer & follow the link below (But try without doing this & goto stage 3) first & please let me kno if that works :-

    http://www.4shared.com/file/76886028/fd4...
    )


    & press download !!!

    3) ReConnect & Turn box back on; goto menu & press 1570 to get into the CASS SYSTEM & turn EMU on

    Reinstall channels & voila

  • Stace Godsell Jun 28, 2009


    Hiya this is what I did & hopefully it'll work for U too -

    1) Deleted all th channels & reset 'factory settings' by entering the code 0000, turned th box off waited a couple of minutes & turned it back on !!!

    2) You may have to redownload channels so reconnect yr box to the computer & follow the link below (But try without doing this & goto stage 3) first & please let me kno if that works :-

    http://www.4shared.com/file/76886028/fd4...
    )


    & press download !!!

    3) ReConnect & Turn box back on; goto menu & press 1570 to get into the CASS SYSTEM & turn EMU on

    Reinstall channels & voila

  • Stace Godsell Jun 28, 2009


    Hiya this is what I did & hopefully it'll work for U too -

    1) Deleted all th channels & reset 'factory settings' by entering the code 0000, turned th box off waited a couple of minutes & turned it back on !!!

    2) You may have to redownload channels so reconnect yr box to the computer & follow the link below (But try without doing this & goto stage 3) first & please let me kno if that works :-

    http://www.4shared.com/file/76886028/fd4...
    )


    & press download !!!

    3) ReConnect & Turn box back on; goto menu & press 1570 to get into the CASS SYSTEM & turn EMU on

    Reinstall channels & voila

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi...juz wanna know wat wud be d possible solution


You don't say whether you use an antenna or cable company. If you use an outdoor antenna then you'll need to get a converter box to get stations now that everything is digital. If you're on a cable system and you have basic cable(no box) then you need to get in touch with the cable company.

Oct 01, 2014 | Televison & Video

2 Answers

Problems on epg information on some channels but not others


Is the episode guide from OTA channels or a set-top box (Tivo, cable)? Make sure that the time is set correctly. In my area, the automatic time information comes from the OTA PBS station. That station's time often is off by a few minutes. (Similarly, when the time is set manually, the clock also drifts on one of my TVs.)

If you get your information from a set top box, try rebooting (or unplugging for a minute) the unit. This sometimes will reset the data.

If those two suggestions don't help, the problem is from the stations/EPG provider. Sometimes the provider's clock is off and this causes the issue. You could try contacting that provider if their clock or program list is routinely off. (If this is related to an event that took longer than scheduled, there isn't much to stop the issue.)

I hope this helps.

Cindy Wells
(Last weekend, my cable box had the correct time. The EPG insisted on showing the programs for 5-6 hours later. Since the provider is a local cooperative, we had to wait until Monday for the support staff to reset the EPG at their computers. Rebooting the set-top box was tried, but didn't help.)

Jun 30, 2014 | Televison & Video

1 Answer

We have a 5 yr old Vizio TV. We did an accidental channel scan, and now cannot get the EPG via the OTA broadcast. Vizio people said, broadcast stations changed the format... so we are out of luck.


Ya you probably need a digital antena adapter box, there cheap you can get them at WalMart. They over the air stations went digital, screwewd every body up. I don't remember how long ago but it was recently. They warned every one ahead of time, but if you had cable you wouldn't have seen the messages, the were broadcast over the air.

Feb 20, 2014 | Televison & Video

1 Answer

StarView SV211K 2-port KVM Switch: my box isnt working only 79 channels are on there....


you only get about 97 chnls on most boxs and the reason why you only have tv2006ect.is you did not download the epg guide with the firmware or you have only been putting in the codes and not the firmware

May 17, 2010 | StarTech.com StarView SV211K 2-port KVM...

2 Answers

Dynex 32 Inch Installation Problem


Hi I Just Bought A Dynex 32 Inch HDTV. I Did A Auto Scan And It Didnt Pick Up Any Digital Channels? Am I Suppose To Have An Antenna Or Digital Box? How Do I Get Th Channels To Come In?

Nov 28, 2009 | Televison & Video

1 Answer

Anybody out there with new ntl codes for Dublin area 28/6/09


Not 100% certain that this'll work even if yrs is a starview5 box but just in case it is but this is what I did & hopefully it'll work for you too - good luck :- Even if not Starview3 it might give U a few tips ;o)
Subject: Star View 3 The Box Super when channels discappear ;o) 1. Press menu then Factory Setting & Enter code 0000 to reset. 2. Exit to main menu & enter 1570 to get into the CASS SYSTEM & turn EMU on 3. Reinstall channels (Goto Installation, Cable network (try TW first & if no channels try NTL then C & W and so on - I'm with Virgin & used the setings for TW) & Voila ;o) Nb: You may have to redownload channels so reconnect yr box to the computer & follow the link below http://www.4shared.com/file/76886028/fd4ac296/GTRom_the_box_Super_8102e_081129.html?err=no-sess & press download !!!

Jun 28, 2009 | StarTech.com StarView SV211K 2-port KVM...

1 Answer

Starview3 super, 3 or 4 Irish channels only, emu switched on.


Not 100% certain that this'll work but this is what I did & hopefully it'll work for you too - good luck :-
Subject: Star View 3 The Box Super when channels discappear ;o) 1. Press menu then Factory Setting & Enter code 0000 to reset. 2. Exit to main menu & enter 1570 to get into the CASS SYSTEM & turn EMU on 3. Reinstall channels (Goto Installation, Cable network (try TW first & if no channels try NTL then C & W and so on - I'm with Virgin & used the setings for TW) & Voila ;o) Nb: You may have to redownload channels so reconnect yr box to the computer & follow the link below http://www.4shared.com/file/76886028/fd4ac296/GTRom_the_box_Super_8102e_081129.html?err=no-sess & press download !!!

Feb 28, 2009 | StarTech.com StarView SV211K 2-port KVM...

1 Answer

Starview3 the box


Hiya this is what I did & hopefully it'll work for U too - 1) Deleted all th channels & reset 'factory settings' by entering the code 0000, turned th box off waited a couple of minutes & turned it back on !!! 2) You may have to redownload channels so reconnect yr box to the computer & follow the link below (But try without doing this & goto stage 3) first & please let me kno if that works :- http://www.4shared.com/file/76886028/fd4ac296/GTRom_the_box_Super_8102e_081129.html?err=no-sess ) & press download !!! 3) ReConnect & Turn box back on; goto menu & press 1570 to get into the CASS SYSTEM & turn EMU on Reinstall channels & voila

Jan 29, 2009 | Linksys BEFSR41 Cable/DSL Router W/4 Port...

3 Answers

Insignia digital tv converter/indoor antenna no signal


Ok first I can save you some money. Take your "HDTV" antenna back. There is nothing different about the antennas needed receive analog and digital signals. If you got reception without your converter box, use the same antenna with your converter box.

Next let's see if there is a problem with the box. Hook up a television with the antenna. How many stations do you get? Now hook up the same television & antenna, but this time put the converter box between the antenna & the TV. Do not turn on the box. Now how many stations do you get? If the number is different, the box is not allowing the antenna signal to pass through. That is bad. You want your signal to pass through the box so you can still pick up stations that don't broadcast digitally. Some areas of the country will not be covered by digital stations from all major broadcasters when the changeover happens in Feb.

My suspicion is either you did not have the antenna hooked up to the converter box when you searched for channels OR you are in an area that is not yet broadcasting digitally.

I hope this helps you solve your problem. Thank you for using FixYa and feel free to add more questions here by using comments.

Jan 09, 2009 | Insignia Digital-to-Analog Converter for...

1 Answer

Remote not working correctly


It all depends on what and how the cable box is connected . Do you have an outside or inside antenna connected? If you have a cable box , why would you want to go to another station on your tv? Does the cable box have an rf output that connects to the tv through he antenna input on the back of the set? If so the tv should stay on a station to recive the stations thru the cable box. Didnt the cable tech explain how to use the system?? If you dont understand how to use the cable you should, for sure call the companey, and see if they can explain how they hooked up your sysytem as theres many many ways to do this. If you have the owners manual what im about to explain is in there too. On the tv remote theres a button called menu, press it once. Use the up and down arrows to scroon down and highlight the setup . press the ok or enter buttonpress the right language,then search for channels. When this is over then exit out of the menu, and try switching channels. If you still dont have any channels you gonna have to find out whats connected to your rf input as channels wont come in if theres not the right source connected. GOOD LUCK

Jun 18, 2006 | RCA G27303HP 27" TV

Not finding what you are looking for?
StarTech.com StarView SV211K 2-port KVM Switch Logo

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top StarTech.com Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18354 Answers

loftys0504

Level 2 Expert

191 Answers

john1601

Level 1 Expert

27 Answers

Are you a StarTech.com Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...