Question about Televison & Video

1 Answer

Fujitsu 52" plasma stays in standby

Hi my plasma comes on then goes back to stanby pls help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 223 Answers

I think you have a fault on the power supply board. If you can check this for yourself if not find a competant technician. Hope this helps.

Posted on Oct 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my samsung crt tv come up on start up but couldn't stay for more than few seconds before it goes standby. I've tried to check settings but could not even get anywhere before it goes back to standby


Whenever a television starts doing this the motherboard/main board and or power supply is usually at fault. The power supply can usually be rebuilt for around $150 depending upon the knowledge and skill of your local television repair shop. To replace the parts is usally more expensive then it would be to purchase another television ($300 and up). Are you sure this is the model number of your television because this model number is not for a CRT television. For troubleshooting you can unplug it overnight to try and power cycle it but it sounds like your problem is beyond doing any type of power cycle to get the television back going again. It would need the repair shop or to be discarded for another.

Oct 29, 2011 | Samsung LNT3242H Television

1 Answer

LG 42 Plasma try's to turn on but just goes back into "stanby" ?


Check to see if you get Va and Vs voltages from the power supply. There should be some wires running to the y-sus. A couple of those wires will be labeled va and vs. Are they present? There will be a sticker stuck to the panel somewhere telling you what they should be.

Mar 26, 2010 | LG 42PC3D 42 in. Plasma Television

1 Answer

Fujitsu Plasma Screen won't power up


This is most likely caused by the Main Power pcb.

See Fujitsu Service Bulletin on this problem in a similar model from Fujitsu. -see link below
http://tomtom2k5.free.fr/fujitsu/PDP-0035-06.pdf

A competent service technician should be able to implement the service bulletin.
A similar service bulletin is probably available for your model. Request bulletin from Fujitsu 'service@fujitsugeneral.com'

May 18, 2009 | Fujitsu Plasmavision PDS-4242 42 in....

1 Answer

Bush lcd 37 inch tv keeps going to stanby


my bush lcd tv keeps staying in standby mode and wont go on if it does go on its only for a minute or two....

Help please

Mar 04, 2009 | Televison & Video

2 Answers

Power on/off


that is a common problem with this rca's check the convergence board for a short circuit
more likely is a transistor or an convergence ic

caypianan@yahoo.com

Jul 18, 2008 | RCA HD52W58 52" TV

1 Answer

Stanby


you might need to balance the standby with the screen saver settings.

Jun 07, 2008 | HP Pavilion dv2000t 14.1" Notebook Laptop...

2 Answers

Fujitsu plasma monitor 42" - keeps going to standby.


It is the soft wear protection system error. You should asked for service.

May 11, 2008 | Daewoo DSP4210GM 42 in. Plasma Television

3 Answers

Stuck on Standby, Fujitsu Plasmavision: Model pds4229e-b


I had exactly the same problem with a Fujitsu General PDS4208E. After looking at the forums etc bit the bullet and tracked down an ORIGINAL remote. Paid yesterday, arrived today - batteries in...screen back on!! One proviso here: Before you pay big money for an original remote (and ONLY they will work with these 2nd generation plasma screens not universal remotes) make sure that your screen WAS working before it was in the standby mode. try http://www.portables.co.uk/ on +44 208 968 1444. Ask for Andy. He seemed to know what he was talking about. About £50 +VAT plus next day delivery charge. Alternatively borrow mine at £5 a button press!! ;-))

Mar 06, 2008 | Fujitsu Plasmavision P42VCA30EH 42 in....

2 Answers

Plasma wnt stay on


I have had this problem in some models of plasma sets before. In most cases the power supply and main drive boards had to be replaced. In a small number of cases the failure was the screen itself.

In all cases, the cost of the repair was expensive. For the screen failure, the set was scrapped.

Jerry G.

Dec 30, 2007 | Hyundai ImageQuest HP4240 42 in. Plasma...

3 Answers

Lg plasma 50px4d-eb keeps going into standby mode


good grief - my TV just did the same thing - its locked in standby mode - I disconnected power several times - each time i reconnect the green light comes on for about a minute 9nothing happens on the screen) and then returns to the stanby mode

Sep 27, 2007 | Televison & Video

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73118 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

yadayada
yadayada

Level 3 Expert

71338 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...