Question about Emerson EWF2004 20" TV

1 Answer

Skipped channel 4

We cannot find our remote control and the TV has channel 4 skipped. We need the TV to be on channel 4 in order to receive the cable signal. Is there anyway to reset the skipped channels without having the remote control?

Posted by on

1 Answer

I have the EWF2004 emerson TV. I tried a ONE For all universal remote and programmed it for a FUNAI TV code 0179 and it worked!!!!!!

Posted on Oct 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jvc gennessa how to scan for channels


need to know if a cable box is used. If using the built in converter there are more than 1 positions that can be selected. On one setting some channels are omitted. A channel scan is usually on the remote that came with the tv. It is under the menu option to do a channel scan.
If some are skipped try to manually put the channels in to see if anything is there.

Mar 19, 2013 | Standard (CRT) Televisions

1 Answer

I need help with channel set up for a sylvania 6432TF tv. i do not have original remote. and it only will go up to 21??


All the other channels might have been skipped by the remote control. Without remote control, it will be impossible to retrieve them.

Aug 22, 2012 | Sylvania 6419TA 19" TV

1 Answer

I can't get my dish system to work with this TV. I'm only getting 2 chanels. How do I program new chanels to this TV? I need chanel 60.


It depends on the TV a bit. Which model of Broksonic TV do you have? Do you have the original remote? (remotes.com has replacement remotes for many TVs.) Look at the TV (or the original remote) for a menu or channel add subtract option. (The TV is probably programmed to skip the channels that didn't have a signal in the past so you need to reprogram this.) If the TV is a really simple TV (with just the channel and volume controls on the TV), you'll need the original or a direct substitute remote (or a higher end programmable remote). Most basic universal remotes will control power, channel and volume but not the reprogram channels option (in my experience). If you can program the add/remove channels, press 60 on the remote, wait for the TV to go to that channel and then press the Add Channel button. Alternately, with the satellite receiver on, press the combination to search all channels and program the skip to channels with signal.

I hope this helps.

Cindy Wells
(I had a really old Emerson TV; when the original remote started to fail, the cheap universal remote didn't handle the channel programming. Fortunately, the original remote would usually still work for that.)

Jul 07, 2010 | Broksonic TV

1 Answer

I have a philips I got from a hotel but i cant program the channel to 3 to hook up a dvd player even with a universal remote what do i do?


Channel 3 is probably locked out... here is how to fix it....

1) Press the Menu button on the remote or press both Volume buttons on the front of the TV to access the TV's internal menu's

2) Scroll to highlight INSTALL using down arrow on the remote or Channel - on the front of the TV.

3) Press the Right Arrow on the remote or Volume + on the front of the TV to access the INSTALL menu.

4) Scroll to highlight Channel Edit using down arrow on the remote or Channel - on the front of the TV.

5) Press the Right Arrow on the remote or Volume + on the front of the TV to access the Channel Edit menu.

6) Use the Left or Right Arrow on the remote or Volume + / - on the front of the TV until you get to Channel 3.

7) Use the Down Arrow on the remote or Channel - button on the front of the TV to select SKIPPED.

8) Press the Right Arrow on the remote or Volume + on the front of the TV to select OFF.

9) When finished press Exit on the remote or press the power button on the TV and then power the TV back on.

You should now be able to use channel 3.

Good Luck....

Jan 15, 2010 | Philips 20PT6441 20" TV

1 Answer

Can't figure out how to turn on cable on Sony Trinitron TV


Setting Up the TV
After you have finished connecting your TV, you can use Auto Program to set up your
channels. During Auto Program, the TV will automatically search for available channels and
program receivable channels.
(Make sure CABLE is connected on coaxial and you are not using any other connections such as cable box, hdtv or satellite antenna)

1 Press to turn on the TV. The Initial Setup screen appears.
2 Press on the remote control or on the TV front panel to start Auto Program, or press
to exit.
To perform Auto Program again
1
Press .
2 Press g to highlight Channel Menu.
3 Press f to highlight Cable. Press to select.
4 Press F or f to highlight On or Off according to how you connected your TV. Press to
select.
5 Press f to highlight Auto Program. Press to search for channels.
6 After Auto Program finishes, press to exit.
To reset the TV to factory settings
1
Turn the TV on.
2 Hold down on the remote control.
3 Press and release the POWER button on the TV front panel. The TV will turn itself off,
then back on.
4 Release .
✍ When you start Auto Program wait until it is finished; otherwise it will skip over channels that are
available. Perform Auto Program again to program receivable channels.
✍ The Initial Setup screen appears each time you turn on the TV until you perform Auto Program.
Initial Setup
Auto Program [CH+]
[CH–]
First please connect
cable/antenna
Exit

Jan 17, 2009 | Sony FD Trinitron WEGA KV-24FS120 24" TV

1 Answer

#4 & #5 buttons do not work on my remote. Channel 55 wont come in either on my tv


I had that problem 2 my channels disapeared one by one and some will skip yes...

I always use on my remote controll :

1 menu
2 Ch tuning
3 auto

and then wait untill it has found all the channels

Oct 02, 2008 | Orion1934 19" TV

2 Answers

Channel memory reset


Bryan,

Usually the menu can be accessed from the buttons on the console, sometimes by pressing a "menu" button but other times by pressing both Volume or Channel (+ AND -, UP AND DOWN) buttons simultaneously. Menu levels are usually selected with one or the other of Volume or Channel, and toggles/selections with whichever doesn't do the levels.

Nov 05, 2007 | Sharp 27K-S300 27" TV

1 Answer

Can't access channels 3 and 4


Open main menu and select manual program. In this option check skip on/off option is there. Otherwise select autoprogram the channels are automatically stored, after completing autoprogram TV displays program edit option. In that you can choose your needs.

Sep 09, 2007 | Zenith SY2751Y TV

Not finding what you are looking for?
Emerson EWF2004 20" TV Logo

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Emerson Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68197 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Are you an Emerson Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...