Question about Denon Audio & Video Receivers

1 Answer

I have a Denon 1650 CD player. Denon doesn't carry the parts to repair it. (Scratchy sound on all CD's). Are there aftermarket parts anywhere? Thanks Ray Durr

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,234 Answers

Based upon your description, the problem is most likely either the D/A converter IC or a bad audio output transistor/opamp. Without seeing the unit, remote diagnosis is just a guess. The IC should be available generically. Can you post a photo of the board? If I can see what is in there, I can point you to the suspect parts. I don't have a service manual for this one.

Dan

Posted on Oct 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Denon c200 is not reading any CD's.


It is very possible that your Denon CD player needs to get the laser lens cleaned.

You can do it yourself taking the cover of and get to the laser lens and clean it.

Here is a site that shows you how to do:

http://www.wikihow.com/Clean-a-CD-Player

or you can purchase a laser lens cleaner CD:

http://www.amazon.com/Allsop-56500-CD-Laser-Lens-Cleaner/dp/B00000J1QK

Regards

Sep 12, 2011 | Denon Audio & Video Receivers

1 Answer

Denon AVR-1908 speaker issue


Before we play taps and throw dirt on top of the Denon, perhaps a bit more triage is in order. I'm not certain who the patient is. Especially when you have "speaker issue" in the title. Are you saying there are some speakers that don't work ONLY with BluRay?

If it has NEVER worked the (unnamed) BD player or its cable(s) could be at fault, too.

What 'connections' are we talking about. HDMI, coaxial- or optical audio, 5.1 analog; to what input on the Denon assigned to what function?

Have you tried all audio paths out of the BD player? Is it configured to squawk in the right digital mode?

Do you have any other digital audio sources (CD/DVD) you could use to certify the audio paths that don't work with the BD player?

Apr 08, 2010 | Denon AVR-1908

1 Answer

Noise coming out of speakers connected to Denon AVR 1908


Check for nearby wireless devices and move them away. -If the audio output from the source device (i.e. DVD, CD player) is digital (i.e. PCM, DTS or Dolby Digital) you're on your own. I'd be willing to bet the output is analog (red and white RCA), because the "beeps" and "exploding sounds" you describe seem like it could be caused by interference. Try replacing the cables. Otherwise the issue is probably with your receiver.

Aug 11, 2009 | Denon AVR-1908

1 Answer

Denon 2802 amp


Dear Armani,

You cannot put de leads from an MP3 player or your TV into the pre-amplified connection of your Denon,
the phono "stage" is a low input stage, your input from MP3, TV, CD, DVD oscasetteplayer is high output (a 5 to 10 times stronger signal)
Try every other stage like tape 1 or 2, this will work just fine,

succes

Apr 30, 2009 | Denon AVR-2802

1 Answer

Picture but no sound on DVD


press "setup" on the remote controller then "OK" go down to OPT1, press left or right arrow to get DVD. 'setup' or 'exit' to exit

Apr 07, 2009 | Denon AVR-1803 Receiver

1 Answer

No dish network sound through denon 1609 receiver


check the setting for the HDMI connection at the Denon you may have to assign the HDMI audio setting also on the front of the Denon while in the DVR mode press the input mode button on the front of the Denon to select auto and if that doesn;t give you sound you will have to connect a cable from the DVR optical.coaxial or analog audio output to the Denon and setup for that type of audio connection

Jan 19, 2009 | Denon AVR588 Receiver

2 Answers

No system configration display on AVR3300 since moving.


Make sure the S-video and the composite cable are not plugged in it the same time from the Denon of at the Plasma

Jan 19, 2009 | Denon AVR-3300 Receiver

1 Answer

Denon AVR 488 got picture but can not get sound


the hdmi does not carry sound on the box its only a pass through, if you want digital quality sound it has to go through dig coax, or preferably optical(toslink)

Jan 09, 2009 | Denon AVR-3300 Receiver

1 Answer

Also problem with Denon AVR-2802


If DIGITAL sign on the display blink, it mean the DSP board is defective. probably the DSP itself

Jul 22, 2007 | Denon AVR-2802

2 Answers

No radio


The front end is bad on this reicever. Your going to need special equipment to trouble shoot this problem, as Its all RF. It is most likly not worth repairing as a shop will most likly charge you more then its worth

Sep 16, 2006 | Denon AVR-1100 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

jonpoint

Level 1 Expert

4 Answers

Tech Leprechaun
Tech Leprechaun

Level 2 Expert

61 Answers

Are you a Denon Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...