- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
After you press the reset. Your laptop has to be physically connected to the router to configure it
Open your web browser, type in "192.168.1.1" and login using username and password. In "Basic setup" DHCP Server should be "Enabled" Enter "Domain name" Name your private network Set the starting IP address - Enter 10 ( any low number) Set time zone Save Settings ( button at bottom of page ) Under Advance Routing, set Operating mode as "Router" Save Settings WIRELESS TAB Wireless - set to MIXED Wireless network name - same as domain name Select a wireless channel (default is 6) Wireless SSID Broadcast - ENABLE Save Settings Wireless Security tab Select WEP Default transmit Key - select 1 Enter a pass phrase to generate a security code, click on Generate
WRITE DOWN THE PASSKEY ( aka, Security code) KEY 1 should have this PASSKEY entered. SAVE SETTINGS On your laptop, right click on the icon for the wireless on the task bar, select "View available networks"
Select your network, it should prompt you for the passkey, you will need to enter it twice
I think you should upgrade the firmware on your router. After upgrading the firmware reset the router and reconfigure it manually. I will also suggest you to create a new wireless network and use security modem WPA. Try to connect to the new wireless network and see if that works.
1.Step 1 Open your web browser, type " http://192.168.1.1/ " into the address bar and hit "Enter." 2.Step 2 Use "Admin" as the username in the pop-up box and leave the password blank. 3.Step 3 Connect to the Internet and click on "Internet Setup." 4.Step 4 Select your connection type from the drop-down menu. Choose "DHCP" for cable modems or "PPPoE" for most DSL modems. If you are unsure of these options, check with your ISP. 5.Step 5 Set a service set identifier (SSID) to identify the router and change the password. 6.Step 6 Encrypt your wireless connection using a Wireless Encryption Protocol (WEP) key. Under the "Wireless Security" option, enter a passphrase and click "Generate." This will generate a password which will need to be used by any client connecting to your router.
If you are trying to connect your wireless router to your ADSL modem then ( ADSL Modem -->Wireless Router-->Your Computer) dont enter any values in the ISP, DNS and MAC address fields. Let them be on default as : Domain
Name Server (DNS) Address
Get Automatically From ISP
Use Default Address This would then automatically pick up the settings from your modem.
You should remember to ad a WEP key to secure your wireless.
Make sure that the wireless switch on your laptop is on. Click on view wireless network by right clicking on the network icon on your system tray. Locate the name of your modem ( SSID ) & enter the wireless encryption key ( WEP ) or password
the internet connection goes into the modem then out to your main computer.
belkin provided you with an address to type in your web browser so you can control the routers settings for wireless ,wep , virtual servers, ect.... The security code to enter the settings by default is blank so just hit submit and you should be in
Looks like when you reset the router you have lost all yur configuration and back to the default factory settings.
Bridge the 5100 first.
1. In your web browser browse to »192.168.0.1 This address will be located on a yellow sticker on the bottom of your modem.
2. The first screen will ask you for your Modem Access Code. This also will be located on the same yellow sticker.
3. Select Advanced from the blue buttons on the left.
4. Click the PPP locations button.
5. The modem may ask your for the Modem Access Code again. If so type it in again and click continue.
6. Select the radio button labeled, "Bridged Mode (PPPoE is not used)"
7. Click Save Changes.
8. A "PPP Location Warning" page will come up. Click "Change PPP Location."
9. A "Restart Needed" page will come up. Click "Restart"
10. Reboot your computer and and then connect the router
11.Configure the router for PPPoE using your ISP uid/pass
12.Configure your wireless using WEP
13.Desktop : Using Dell wireless client configure the client using the same SSID ,wep as configured in the router
Laptop : follow the same as desktop
(by default dell wirelesss client takes over the wireless configuration in dell pc.to disable it and use windows wireless client..control panel ->administrative tools -> services -> enabl2 wireless zero configuration)
14.after all configuration shut the desktop,laptop,router,mdm and pwr them in seg..first modem and then router and then your desktop or laptop
As you ave the modem in bridge mode and also it works ine with wired connection just follow the instruction below for wireless
1.Login in to the router - > wireless settings
2.Configure your wireless using SSID and WEP and save settings
3.Laptop : Using windows wireless client configure the client using the same SSID ,WEP as configured in the router(view available wireless network in wireless properties)
(by default OEM wirelesss client takes over the wireless configuration in branded pc.to disable it and use windows wireless client..control panel ->administrative tools -> services -> enabl2 wireless zero configuration)
14.after all configuration shut the desktop,laptop,router,mdm and pwr them in seq..first modem and then router and then your desktop or laptop
Have you tried inputting the necessary security code to your HP laptop? Most if not all BT1800HG wireless router modem comes pre-configured to use a certain WEP code.
In your HP laptop go through the WiFi configuration/Setup. Select option to use WEP security, type in required code normally found on the bottom of the BT1800HG. The numbers and/or characters below the bar code is the WEP code.
Hope this be of some help/idea. Post back how things turned up or should you need additional information.
Good luck and kind regards.