Question about GE Energy Star 3.7 IEC Cu. Ft. Front Load Washer with Stainless Steel Basket

3 Answers

Ge Adora front load washer not working

My washer makes 6 buzzes from front door no matter what i do and will not go into diagnostic mode just starts the pump every time i try to do anything. i hit signal delay signal delay and it buzzes 6 time then starts the pump. i put it on rinse spin and it buzzes 6 times then starts pump. door stays locked and have to manually release every time. could it be a main board problem? please say no... i just replaced the pressure switch due to being told by someone else that if it won't go into diagnostic mode that would be it, wrong did same thing.. model # is whdvh626fww

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers

Hi,

I don't know how you could have got it into diagnostics mode by accident - - but here's how it goes . Hit the power button until there is NO display . Unplug and wait a minimum of 30 seconds , plug back in and within 30 seconds hit SIGNAL button then DELAY START button then SIGNAL button again then DELAY START button again. door should lock and display t01 It is now in test mode . There are 14 different test it can run through in this mode , but all we are trying to do is check for error codes now and maybe get you back to normal, So turn the knob one click clockwise and hit the START/PAUSE button and see if any error codes come up. To exit the diagnostic mode - hit signal button then delay start button then signal button then delay start button and you are out of service test mode and back to normal

Posted on Sep 30, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 409 Answers

Hi there,

i would recommend to do a couple of checks before replacing any more parts:

check the door latch and make sure that the switch is engaging correctly. the buzzing may be coming from the door switch not engaging correctly.

from the sounds of your problem, you may have an intermittent door latch.

may i ask why you are running a diagnostic?

what was the original problem?

thanks

Posted on Sep 30, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,879 Answers

The main board is not doing what it is supposed to do. It controls everything, that's why replacing the pressure switch didn't fix the problem.

Posted on Sep 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ge adora washing machine beeps when pushing start with door closed


Hit the power button until there is NO display . Unplug and wait a minimum of 30 seconds , plug back in and within 30 seconds hit SIGNAL button then DELAY START button then SIGNAL button again then DELAY START button again. door should lock and display t01 It is now in test mode . There are 14 different test it can run through in this mode , but all we are trying to do is check for error codes now and maybe get you back to normal, So turn the knob one click clockwise and hit the START/PAUSE button and see if any error codes come up. To exit the diagnostic mode - hit signal button then delay start button then signal button then delay start button and you are out of service test mode and back to normal. Post any error codes.

Dec 07, 2012 | GE WSXH208A Front Load Washer

1 Answer

GE Adora front load washer turns until water is added then won't turn or spin


You should contact GE or qualified appliance repair center to be looked at professionally.

May 06, 2012 | GE Wh12x10309 Heater for Adora Front Load...

1 Answer

GE Adora front load wont lock the door or start at all. GE service is not existant.


the door switch has broken and needs replaced can be got online,adrian;;;;

Nov 11, 2009 | GE WSXH208A Front Load Washer

1 Answer

My washer will not start. I press the start/pause button and it just beeps twice and does not lock door or start wash. ge adora model wcvh6260


clean the drain filter located behind the front lower panell, its prob. holding excess h2o and wont let the water fill cycle activate. this happened to mine.

Aug 11, 2009 | GE Energy Star WCVH6260F Front Load Washer

1 Answer

My washer will not start!!


Does the start/pause button flash and then the door unlocks? I had that problem too. This is what I did. I found the solution to clean the lint filter on the GE Adora. Go to http://www.instructables.com/id/GE-Adora-Lint-Filter-Cleanout/?download=pdf

I just did this and my washer is now running instead of the flashing start/pause and door unlocking. It was fairly easy. Make sure you have towels and a flat pan to catch the water if you don't have the machine on a riser. There may be water inside so a wet vac may be helpful too. Once my washer finishes what was in it, I have these funky towels to clean. You'll be very surprised what you find in the filter! Best of luck!

Oct 19, 2008 | GE WSXH208A Front Load Washer

2 Answers

Front load ge washer does not finish cycle


This model does not have a drain filter. There are filter screens inside the inlet valve where the hoses attach onto the machine. Take hoses off and look inside where the water goes into machine to see screens. Also, take the other end off hoses to make sure there are not screened hose washers in either end of the hose which may need to be cleaned or replaced.

Oct 18, 2008 | GE WSXH208A Front Load Washer

1 Answer

Ge front load washer model WSXH208A Will not spin


Mine kept stopping mid cycle also, pouring water on the floor, then the start/pause button flashed and the door unlocked. I found the solution to clean the lint filter on the GE Adora. Go to http://www.instructables.com/id/GE-Adora-Lint-Filter-Cleanout/?download=pdf

I just did this and my washer is now running instead of the flashing start/pause and door unlocking. It was fairly easy. Make sure you have towels and a flat pan to catch the water if you don't have the machine on a riser. There may be water inside so a wet vac may be helpful too. Once my washer finishes what was in it, I have these funky towels to clean. You'll be very surprised what you find in the filter! Best of luck!

Oct 13, 2008 | GE WSXH208A Front Load Washer

1 Answer

Wont spin


I found the solution to clean the lint filter on the GE Adora. Go to http://www.instructables.com/id/GE-Adora-Lint-Filter-Cleanout/?download=pdf

I just did this and my washer is now running instead of the flashing start/pause and door unlocking. It was fairly easy. Make sure you have towels and a flat pan to catch the water if you don't have the machine on a riser. There may be water inside so a wet vac may be helpful too. Once my washer finishes what was in it, I have these funky towels to clean. You'll be very surprised what you find in the filter! Best of luck!

Sep 17, 2008 | GE WSXH208A Front Load Washer

1 Answer

Washer won't drain


http://www.instructables.com/id/GE-Adora-Lint-Filter-Cleanout/?download=pdf

Had the same problem, this fixed it!

Aug 05, 2008 | GE Energy Star WCVH6260F Front Load Washer

2 Answers

GE Energy Star WCVH6260F Front Load Washer: door locking problem


http://www.instructables.com/id/GE-Adora-Lint-Filter-Cleanout/?download=pdf

Had the same problem, this fixed it!

Mar 12, 2008 | GE Energy Star WCVH6260F Front Load Washer

Not finding what you are looking for?
GE Energy Star 3.7 IEC Cu. Ft. Front Load Washer with Stainless Steel Basket Logo

914 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Tim Whalen

Level 3 Expert

3069 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...