Question about Lexmark E232 Laser Printer

1 Answer

E232 The light for the Photoconductor is constantly on,even when using a new photoconductor still same error and printer not printing at all.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem. At least not it's printing but the lights still on. But while researching on the Lexmark Website I see that this printer has a recall. Check the website for additional details.

Posted on Nov 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lexmark E232 secon light from the top keeps blinking I think this is ink, I can print a test page and it is nice and dark and prints fine


This light sequence means that the photoconductor kit's drum is almost full and will need replacing soon. For more information on how to replace photoconductor, click on the link http://bit.ly/oD75Kw


For additional assistance, please contact Lexmark Technical support

Jul 21, 2011 | Lexmark E232 Laser Printer

1 Answer

I replaced my photoconductor and now my printer won't print. The toner button and ! button flash.


The photoconductor kit's drum is full and needs replacing. The printer will not print any more pages until the photoconductor kit is replaced.

Click on the link http://bit.ly/oD75Kw to see instructions on to replace photoconductor.

For further assistance, please contact Lexmark Technical Support

Jun 06, 2011 | Lexmark E232 Laser Printer

1 Answer

Printer printed out error message stating that the photoconductor kit had worn out, so I ordered and installed a new one. However, the printer continues to print the same error message and nothing else....


After replacing the photoconductor kit, you will need to reset the photoconductor page count. Here's the link for instructions on how to reset the page count: http://bit.ly/agYtVo . Or simply press and hold the CANCEL button while the printer is on and the front cover open until all lights are flashing. Hope this helps. If you need more assistance, leave a comment and I'll get back to it. Thanks.

May 27, 2010 | Lexmark E232 Laser Printer

1 Answer

How do you remove the old Lexmark E232 photoconductor and install the new Lexmark E232 photoconductor?


Hello. I hope you got it working already. If not, here's a link to the Lexmark website to guide you on how to install/replace the Lexmark E232 photoconductor. Just click on this link: http://bit.ly/cWGimB. Don't ignore WARNING, NOTE, and IMPORTANT. Hope this helps. If you need more assistance, leave a comment and I'll get back to it. Thanks.

Apr 23, 2010 | Lexmark E232 Laser Printer

1 Answer

How do I replace the photoconductor where is the menu button to reset PC CNT appears after it is replaced?


Power the printer on and get it to the Ready state. With the printer on and in the Ready state, open the front cover.
Press and hold the Cancel button until all of the lights begin flashing up and down.
Release the Cancel button and close the door. The photoconductor count should now be reset.
To confirm that the photoconductor page count has been reset, it is recommended that you print a menu settings page and check the photoconductor level. Do the following:
With the printer at the Ready status, press the Continue button once. The Ready light will begin flashing and one or two pages will print out.
Look for a section labeled Cartridge Information and locate the word Photoconductor under this heading.
Confirm that the photoconductor level reading is either OK or close to 100%.
If the reading is low, try printing 10 - 20 pages. Print the menu settings page(s) again.
Confirm that the photoconductor level reading is OK or close to 100%.
Good luck, Gerrit Jan

Oct 29, 2009 | Lexmark E232 Laser Printer

1 Answer

Photoconductor kit


you must reset the error message; find the explanation in the photoconductor kit package

Sep 29, 2009 | Lexmark E238 Laser Printer

2 Answers

Lexmark E232 Printer prints all characters fine but leaves about an inch gray/black margin on the left side of the paper. Tried replacing the toner cartridge and it didn't help. Any suggestions?


If this model has separate toner and photoconductor then the photoconductor is at end of life and needs to be replaced. Follow the directions that come in the new photoconductor package to install and reset the PC count this is important.

Luck

Mar 07, 2008 | Lexmark E232 Laser Printer

2 Answers

Photoconductor led blinks constantly along with the attention light


You need to reset the Photoconductor counter this can be done when the printer has cycled as far as it can go open the door and hold the second button down until all the lights have cycled once then close the door and you should be set to print.

Good luck

Jan 17, 2008 | Lexmark E232 Laser Printer

2 Answers

Lexmark E232 photoconductor


Make sure to install the new photoconductor 1st.

1) Power off the printer using the switch in the back.
2) Open the front cover.
3) Press and hold the Continue button (Big silver button with Diamond shape symbol) and power the printer On (turn the switch back to ON).
4) When you see the last light i.e. error light on solid, release the Continue button and close the front cover.
5) When you close the cover you will see all the top 3 lights on solid.
6) Press the cancel button with X symbol for 4 times very slowly till you see toner low light (i.e. second light from top) on solid.
7) Press the continue button and wait until you see the light sequence.
8) Press the cancel button and wait until you see the light sequence.
9) Finally power off the printer using the switch in the back (IMPORTANT= wait 1 minute) and power it back on to exit the configuration mode.

Nov 07, 2006 | Lexmark E232 Laser Printer

Not finding what you are looking for?
Lexmark E232 Laser Printer Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...