Question about EnGenius Lands Phones

1 Answer

Register handset to base unit on sn-920 - EnGenius Lands Phones

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Press menu 6 on handset then press base station reg key for 2 sec till L1 L2 L3 L4 LIGHTS FLASH


handset should now show registration no between 10 and 99

Posted on Sep 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can i register my hanset. it says error.


Please use the below link to assist you with handset registration.

http://service.us.panasonic.com/OPERMANPDF/KXTG5621S.PDF#page=35

May 06, 2014 | Panasonic KX-TGA560 Cordless Expansion...

2 Answers

Can not get the second handset to register to the base


This is the registration procedure

Step 1: press MENU-6 and select 3 “SET BASE”
Step 2: press the REG key on the master base
Step3: press register to finish the registration procedure.
• After the registration complete, handset 11 and handset 21 can
2-WAY intercom with each other

If issue persists reset the unit start registration by using 2nd unit that currently unable to register. if issue continues please inform for further troubleshooting

Good Luck

Jan 01, 2008 | EnGenius SN 920 Ultra Cordless Phone

1 Answer

How do i sync my panasonic phones cordless kx-tga810


335 is the magic code when you want to remove a previous handset or base station registration!
Handset:

1 " (middle soft key) i L i #

2 Enter "335".

3 "Cancel Handset" i #

LThe numbers of all handsets

registered to the base unit are

displayed.

4 Select the handset(s) you want to

cancel, by pressing the desired handset

number. i #
5 "Yes" i # i {ih}
Base Station:

A handset can be registered to a maximum

of 4 base units. A handset can cancel a base

unit that it is registered to. This allows the

handset to "forget" the base unit.

1 " (middle soft key) i N i #

2 "Registration" i #

3 Enter "335".

4 "Cancel Base" i #

5 Select the base unit(s) you want to

cancel, by pressing the desired base unit

number. i #
6 "Yes" i # i {ih}

Dec 23, 2013 | Panasonic KX TGA810 1Line Cordless...

2 Answers

I am trying to replace a handeset on my E5640 answering system. I have followed the procedures to deregister the existing handsets but it will not accept the base code for the last one. The handset I am...


  • Your telephone can accommodate up to four cordless handsets. You can add new handsets (Model E560-2, sold separately) at any time, but each must be registered with the base before use.
  • The handset provided with your telephone is automatically registered as Handset 1.
  • Additional handsets will be assigned numbers in the order they are registered (2, 3 or 4). You can register a maximum of four handsets.
To de-register all handsets
• Unplug the power supply from the base unit.
• Remove all handsets from the charge cradles and base.
• Plug in the power supply while pressing and holding the HANDSET LOCATOR button.
• Continue pressing HANDSET LOCATOR until the IN USE and CHARGING indicators are lit (this could take up to 10 seconds).
• Release the HANDSET LOCATOR button.
• All handsets will display: ENTER BASE ID: XXXXXXXXXX
Once the base indicators turn off (up to 30 seconds), the handsets have been de-registered from the base, and can now be re-registered.

To re-register a handset:
• Make sure your handset batteries are properly installed and charged.
• Your handset will display "ENTER BASE ID".
• Enter the 15-digit Base ID number from the bottom of the base unit.
• Press SELECT to accept the new code and complete re-registration.

To re-register a handset to a new base unit:
• Make sure your handset batteries are properly installed and charged.
• Unplug the old base unit. Your handset will display "SEARCHING...".
• Install the new base unit by plugging it into an electrical outlet and phone jack.
• Press and hold the SELECT key until the handset displays "ENTER BASE ID".
• Enter the new 15-digit Base ID number from the bottom of the new base unit.
• Press SELECT to accept the new code and complete re-registration. The handset is now registered to the new base.

Jun 25, 2011 | AT&T E5640 Phone

1 Answer

How do I deregister my handsets on my VTech 2656


To be able to register your replacement handset, you must de-register all the handsets from the VT2656 base unit.

Follow the steps below to de-register your handset(s) from the VT2656 base:

1. Take out the handset that sits on the base.
2. Unplug power from the base.
3. Hold down PAGE while reconnecting power. When the In Use light blinks, release the PAGE key.
4. Hold down PAGE key for 5 seconds. When the In Use light begins to flash, release the PAGE key.
5. The handset charging light will blink 5 times. Within 5 seconds from when it stops blinking, press PAGE once.

You must register the handset(s) by following the steps below:

1. After charging the handset, remove it from the cradle, the LCD display will read "SEARCHING FOR BASE".
2. Press "NEW" and then enter the 15-digit Base ID code, located on the underside of the VT2656 base unit.
3. Press "OK". The handset will display "PLEASE WAIT!!".
4. Wait approximately 15 seconds. The handset will display "FOUND BASE". If the handset displays "BASE BUSY TRY LATER", this indicates that the system is in use. Wait until the base unit is in the idle (on hook) mode and repeat steps 2-4.

Apr 30, 2010 | Vtech Digital Cordless Telephone VT-2568

1 Answer

TOO FAR FROM BASE


Hi! This may cure your problem!
Re-registering the handset
If “No link to base. Move closer
to base, try again.
” is displayed
even when the handset is near the base
unit, you may need to re-register the
handset to the base unit.
Important:
LMake sure the base unit is not being
used.
LHave the handset and base unit near
each other when re-registering the
handset.
LKX-TG5422 and KX-TG5423 only:
Confirm the extension number of the
handset which has lost its link to the
base by placing the handset on the base
unit or charger.
If you accidentally assign another
handset’s extension number to it, the
other extension will stop functioning.
1 Handset:
Press {MENU}.
2 Scroll to “Initial setting” by
pressing {V} or {^}, then press {>}.
3 Scroll to “Registration” by pressing
{V} or {^}, then press {>}.
4 KX-TG5421 base unit:
Press and hold {HANDSET
LOCATOR
} until the CHARGE
indicator flashes.
KX-TG5422 base unit:
Press and hold the handset locator
button that corresponds to the handset
you want to re-register ({HANDSET
LOCATOR
1} or {HANDSET
LOCATOR
2}) until the CHARGE
indicator flashes.

Below is a link that will take you to the instruction manual for your phone.

http://www.phone-manuals.com/panasonic/KX-TG5422M.shtml

Hope this helps! Hal

Feb 27, 2009 | Panasonic KX-TG5422M Cordless Phone

1 Answer

Can I use handsets from another DCT 748 unit to expand my DCT 748


Short answer:
No. This model of phone can only support 4 handsets. If you need more than that, you will need to have a second base unit.

Detailed answer:
One of my handsets went bad, and I just bought complete DCT748-4 package from a seller on eBay for a very good price. This set was used, but in very good condition. I didn't need the whole set - just one handset - but like I said, it was a good price. Anyway, I began by telling my old base unit to de-register handset #2 (the failed unit). However, I then found that I could not register the "new" handset with my old base unit because it was already registered to the "new" base unit. So, I first had to apply power to the "new" base unit and de-register the handsets. Then, I placed one of the "new" handsets onto my old base unit, and it said "Handset Registering ..." and registered just fine. Just for the fun of it, I placed one of the other spare handsets into my old base unit. It said "Hanset Registering ..." but then it beeped and said "Registration Failed." This is because I already had 4 handsets registered to my base, and the base can not handle a fifth handset.

Feb 15, 2009 | Uniden DCT-748-4 Telephone

1 Answer

BT XD5500 manual


BT Freelance XD 5500

Resetting the base & handset/s on a BT Freelance XD5500:

Hold the Find button on the base unit until you get a double beep then
tap the Find button 7 times.
On the handset:
remove a battery
hold the menu key and refit the battery
screen says SW VERSION
press up arrow key until screen shows REGISTER CLEAR
press menu
press menu again and wait for OK to appear
remove a battery and refit

Registering the XD5500 handset.
Then register the handset to the base as follows:
Hold Find button on base unit until you get two beeps
On handset:
Press menu
Scroll to register
Press menu
Scroll to Register Base
Press menu
Press 1
Wait
When it says PIN ? Enter 0 0 0 0 (four zeros) and press menu.

Note:
If you have more than one handset then repeat registering the handset to the base for each subsequent handset/phone.


If this procedure fails to solve the issue, then you have a unit with a
fault and if it is less than a year since purchase the retailer should
change it for you.

Aug 03, 2008 | Lands Phones

1 Answer

Cordless phone EnGenius SN 920


. A new handset arrives with a handset ID number of 00, to register this handset to your system take the following steps:
  1. On the EnGenius base unit press and hold down both the "Volume" & "Intercom" buttons for about five seconds. You will hear a beep from the base unit. You can now release the two buttons.
  2. On the EnGenius handset (00), press the following buttons: "menu", "6", "1".
  3. A new handset ID number (ie: 12, 13, 14…) is automatically assigned by the base and registration is complete.

Feb 29, 2008 | EnGenius SN 920 Ultra Cordless Phone

1 Answer

ID Conflict with Base 1 error


hold the volume and intercom buttons together the in use light will come on and then go to menu on handset press 6 then 1 to regester that should work i just talked to a friend with a telecom buisness and he told me what to do with mine good luck

Jan 08, 2007 | EnGenius SN 920 Ultra Cordless Phone

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top EnGenius Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

John L radiodude365

Level 3 Expert

488 Answers

Bill Boyd

Level 3 Expert

37973 Answers

Are you an EnGenius Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...