Question about Porter Cable FR350A Factory Reconditioned 3 1/2" Round Head Framing Nailer Kit, 70 120 Psi

1 Answer

Spare Parts needed for MS200

Please advise where I can purchase some spare parts for my Porter Cable MS200?
an internal plastic assembley has broken, it houses a coil spring and retaining ring.
diam of plastic assembley is 1/1/2 inch
diam of spring is 7/8 inch x length 1inch
Diam of ring 1/3/8 inch
I am unsure of the part number and I need the part sent to Queensland Australia post code 4212.
Thanks
Eddy

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Not to sure where to buy parts other then from a dealer. i also had this same gun and had the thing happen to me with the plastic assembley if i was you i would just spend the extra money and get Stanley Bostitch guns, or Senco guns, and get ride of the porter cable guns because they are built cheap. but if you must keep this gun you can check www.deltaportercable.com for parts

Posted on Sep 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Air pops or releases to fire, nail does not fire. Not jammed. Had been working fine, and stopped out of the blue during use.


Betty,The drive pin(hammer) is stuck in the down position and must forcefully be pushed back up,make sure tool is disconnected when working on it. Links below may be of help.
How To Diagnose An Air Nailer

http://www.powernail.com/home/troubleshoot.htm

Porter Cable PCB220TS trouble shooting Porter Cable Air Nailers

Feb 22, 2016 | Nailers

1 Answer

My porter cable roofing nailer rn175 type 1 it fire's and the rod stayed out and air comes out what part do I need to fix


Could have check valve out of place or broken. Easy to check. Remove head and pull out the cylinder and the round cylinder spacer. Look for black band that should have been covering small holes just below the cylinder spacer. Replace band if broken or if good install the cylinder ring on the cylinder then install the band and finally reinstall the assembly into gun. Look for any broken/cracked parts in the head of the gun. Good luck

Aug 28, 2013 | Porter Cable RN175 Roofing Coil Nailer

1 Answer

Using a Porter Cable RN175A and it stopped working.


for technical service (888) 848-5175

866-375-6287 their number

http://www.ereplacementparts.com/porter-cable-rn175-type-roofing-nailer-parts-c-129_1658_1660.html

Sep 06, 2012 | Porter Cable RN175 Roofing Coil Nailer

1 Answer

Air just blowing through and out the top discharge valve


Air leaking from top of nailer is indication of bad cylinder seal. Remove cap and look for loose fitting or broken cylinder seal (vinyl ring). The seal should fit snugly around headvalve. If seal seems ok then remove upper bumper and look for cracks (round vinyl part pushed into center of headvalve). Replace as needed. If all parts look good, and while you have the head valve out, clean the upper head and lube with plenty of silicone paste (sold at Lowes in the plumbing department, used for faucet orings ). Parts are sold at your local dewalt repair center or at www.toolpartsdirect.com.

Jul 31, 2011 | Porter Cable Cable Factory Reconditioned 2...

1 Answer

I have a Porter Cable FR350A Round head framing nail gun, but I dont have none of the accessories in the box. The manuel extra trigger or what ever else that comes in the carrying box when you puchase a...


Parts /extra trigger for your gun are available at your local dewalt service center or at www.toolpartsdirect.com. Some of the triggers that come with fr350a as standard equipment had a small red button on the side that allowed you to select single shot mode or multiple. If your gun has a black metal trigger, it is better quality/lasts longer than black plastic. Good hollidays

Dec 30, 2010 | Porter Cable FactoryReconditioned DA250BR...

1 Answer

Drive rod will not return to top position.


Open up the owners manual, review the parts list diagram blowup. remove the four screws (allen key) and pull top head off unit. You need to get at part #116, a plastic shock absorber that breaks off and falls between the main drive piston and part #120 piston cup. its a $15 part and $10 to ship it.

Dec 18, 2010 | Porter Cable RN175 Roofing Coil Nailer

2 Answers

My Porter Cable FN250A only shoots nails sporadically. When I lift up the nose piece, it appears that the "hammer" is not fully retracting.


Piston not retracting is caused by several issues. Bent or broken driver, worn piston oring or loose or broken check seal. Remove head and examine driver for bent or broken, adjust as needed. Check that piston oring fits snug, piston should not drop down cylinder under its own weight. Pull cylinder from body and check that black band (check seal) is in place around holes in cylinder. Good luck

Oct 26, 2010 | Porter Cable Nailers

1 Answer

I have two Porter Cable pneumatic nailers, one a finish and one a brad. Both of them have suddenly quit working. The triggers are loose and not engaged to anything. Somehow the mechanism is not rebounding...


the triggers are held in place in the handle with two roll pins. the trigger itself operates off a hinged paddle inside the trigger. this paddle won't operate unless the safety is depressed. both safeties have a return spring. if yours are missing nothing will work. go to porter cable parts site and purchase the correct parts

Oct 22, 2009 | Porter Cable Nailers

1 Answer

Need parts for roof nailor in michigan


You can get parts at any dewalt service center. Go to dewaltservicenet.com and enter your model number in the model field then press go. (Please note pressing enter will not get you where you want to go.)

Find the parts you are looking for on the diagram and then locate a service center that is close to you. You may also order parts directly from this site.

Sep 09, 2009 | Porter Cable Nailers

Not finding what you are looking for?
Porter Cable FR350A Factory Reconditioned 3 1/2" Round Head Framing Nailer Kit, 70 120 Psi Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porter Cable Nailers Experts

John Trevino

Level 3 Expert

1378 Answers

Stephan Reichert
Stephan Reichert

Level 2 Expert

194 Answers

yoopertech

Level 2 Expert

121 Answers

Are you a Porter Cable Nailer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...