Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Something stuck in drum, spinning cycle loud hammering/clacking sound

During the spinning cycles my washer has something stuck in it that begins a hammering scraping noise.  We don't want this to effect the motor and it is annoyingly loud.

Posted by on

  • Anonymous Mar 26, 2014

    Sound like scraping when spinning

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 409 Answers

Hi there,

sounds like you may have something caught between the tumbler and the cabinet. since the drum has holes in it, can you have a look if you can see anything that's come of clothing, like a bra wire. it's usually something bigger.

Posted on Sep 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

During spin cycle the washer makes a loud thumping noise. Not a clanging/sharp noise. When I manually turn drum it sounds like something is loose inside. Like a ball may sound inside drum as it turns.


Is it a front loader? You may have something stuck between the tubs or it may be a broken "paddle" One of the plastic baffles that move the clothes around in the tub. they should all be tightly against the tub.

May 26, 2015 | Washing Machines

1 Answer

Final high speed spin very noisey


Something is causing the drum to be way out of balance. Does it bang and make noise when it's spinning empty? Probably not. Is something stuck on the side (inside of course) of the drum, causing it to shake when spinning? If not, a spring or shock absorber (connecting drum to sides, bottom or top of machine) has broken or come loose.

Nov 23, 2013 | Malber WD1000 Front Load Washer/Dryer

1 Answer

Washer making loud noise and wont spin


Check and see if the inner drum is loose and floppy.if it is, it's likely the bearings have collapsed, and require replacement...If the drum feels stiff and tight, it could be that something is jammed between the inner and outer drums. Both situations could be costly...Get quotes....Good luck...Nomess

May 22, 2010 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Kenmore he2plus vibrate very badly, it is level how do i fix this


My HE2T was making a horrendous sound during the spin cycle. It was making a loud clacking sound and the machine was moving all over the place.

There are two things to check. The first is that the feet are on the floor and the machine is level. The second is a bit more complex. Remove the three screws that hold the lower panel. Underneath the drum on each of the four corners are suspension rods. One side is attached to the drum and the other side is bolted to the bottom of the washer. My bolts loosened up which allowed the suspension rods to clack back up and down as the drum spun. You'll need to tighten those bolts very tight and then give it another try.

Attached on the inside of that cover is the troubleshooting guide. There is a manual diagnostic mode and you can step it to the spin cycle so that you can test the spin balance without having to run through a full cycle. Make sure you have some clothes in there during the test.

Jan 09, 2010 | Kenmore HE2 Plus Front Load Washer

2 Answers

My kenmore he2t is very noisy due to the spin cycle. It shakes the whole upstairs


My HE2T was making a horrendous sound during the spin cycle. It was making a loud clacking sound and the machine was moving all over the place.

There are two things to check. The first is that the feet are on the floor and the machine is level. The second is a bit more complex. Remove the three screws that hold the lower panel. Underneath the drum on each of the four corners are suspension rods. One side is attached to the drum and the other side is bolted to the bottom of the washer. My bolts loosened up which allowed the suspension rods to clack back up and down as the drum spun. You'll need to tighten those bolts very tight and then give it another try.

Attached on the inside of that cover is the troubleshooting guide. There is a manual diagnostic mode and you can step it to the spin cycle so that you can test the spin balance without having to run through a full cycle. Make sure you have some clothes in there during the test.

Oct 25, 2009 | Kenmore Washing Machines

2 Answers

Whirlpool washer; spin cycle not draining


It sounds like your water pump is broken. there is a motor inside that pumps the water out when the machine computer changes to spin cycle

Aug 06, 2009 | Whirlpool 4.0 Cu. Ft. Plus Washer

1 Answer

Duet ht something stuck


try a magnet ?..see if you can get it back out the way it went in..good luck doing this without disassembly

Nov 24, 2008 | Whirlpool Gold Duet GHW9400P 3.8 Cu. Ft....

1 Answer

Maytag Washer HAV2558AWW loud noise during spin cycle


Your maytag is really an amana and the bearings are bad. Yes it does cost a lot. If i were you i would buy another washer. Get a whirlpool. (whirlpool now owns maytag)

Nov 16, 2008 | Maytag Atlantis MAV6000 Top Load Washer

2 Answers

Washer makes loud knocking noise


I think that the drum bearings have gone on the machine..

To open the door and spin the empty drum quickly by hand and you should hear the noise or say a less amplifed one.. You can also move the inner drum up and down to see if there is something wrong with it..

Sep 28, 2008 | Roper RAS6233KQ Top Load Washer

1 Answer

"howling" noise during spin cycle (still there after changing burned off belt)


Travioso, there was two service flashes out on this model concerning the seal and bearing which means they had an issue with this washer. The howling noise you are hearing is the bearing and will need the new designed triple seal and bearing kit. This should be covered under your warranty, I believe it is 5 years. The numbers for the service flashes are TDL-0048A-B. Call Maytag and inquire about these service flashes, these should be covered. Catriver.

Jul 25, 2006 | Maytag SAV5701A Top Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

830 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...