Question about Phones

1 Answer

Lost my Owners Manual. Need to know how to put numbers into speed dial-900MHz. I had changed phones and what I had bought could not touch my Uniden! I think the manual is stored in my shed-where is the problem!

Posted by on

  • Carl Navarro
    Carl Navarro May 11, 2010

    A lot of words not saying much is what the problem is.

    Make and Model of your cordless?



×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Looked farther on your site and found out how to get the info I needed. All done. Thank you for answering. I just did read enough to get the answer I needed, it was there, I just missed it the first time I looked at your site.

Posted on Oct 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need instruction manual to program speed dial


I was unable to locate a user manual for that particular device, however the basic instructions for programming speed dial functions are normally very similar between most phones.


Generally there are ONE TOUCH Speed Dial buttons labelled something like M1, M2, and M3 on the dial pad somewhere.


There should also be another button labelled PROG or STORE on the keypad as well.


Normally to program a number into a ONE TOUCH speed dial memory location you carry out the following procedure:


Lift the handset.


Then press the PROG (or STORE) button.


Now just use the number keypad to dial the full telephone number that you want to store in a Speed Dial location.


Once the full telephone number is dialed, then push the M1 button to store that phone number in the M1 One Touch Speed Dial location.


The phone may or may not show some kind of confirmation that the M1 location was just programmed, then just hang up the handset.


Now when you lift the handset and press the M1 button, the phone should automatically dial the phone number you programmed into it.


Now just repeat the same process for the M2 and M3 One Touch Speed Dial buttons with other phone numbers if necessary.


To change one of the Speed Dial numbers, just carry out the normal programming procedure for that location using the new phone number and the old number will simply be overwritten.


I truly hope that was helpful to you.
Good luck and take care.

Joe.

Dec 02, 2011 | Southwestern Bell FM-480 Corded Phone

1 Answer

I need to know how to program phone numbers for speed dialing. I have lost the manual/user guide for my KX-TC1460W


go to your contacts choose a contact choose edit then add a speed dial number

Jul 16, 2009 | Phones

1 Answer

I can't change the speed dial numbers on my phone


You should only have to hit Feature - Redial and then select the soft key that you wish to re-program. Typically you will then type 1 and then the extension you want to program.

Jul 06, 2009 | NEC Electra Elite DTU 16D-2 Corded Phone

2 Answers

Setting the speed dial numbers.


When phone is on standby press memory-the talk led lite should flash. enter the phone # you want to store then push memeory again. Select the speed dial # you'd like to use for this phone # (0-9) then you should here a tone indicating it was successful. Let me know if this works for you-it should!!

Nov 12, 2008 | Uniden Cordless Phone

3 Answers

Lost the instruction book to my Uniden 900MHz phone


Hi

I have a Uniden 2.4GHz Cordless phone.
I need to rececord my greeting on my Answer Machine but have lost my instruction book and dont know which button to press .
Can you help

Feb 21, 2008 | Uniden Cordless phone EXS9950

1 Answer

Uniden 900MHz phone model EX17960A


Using the Speed Dial Memory
Storing Numbers in Speed Dial Memory
Your cordless phone can store up to ten numbers in the speed dial memory.
1) When the phone is in standby mode, press the memory key. The talk/batt low LED flashes.
2) Use the keypad to enter the phone number; each number can be up to 20 digits.
7
3) If you need the phone to pause during the dialing sequence, press
the redial/p key to insert a two-second delay between the
numbers. You can enter multiple pauses to increase the delay.
Each pause counts as a digit.
4) Press the memory key again.
5) To store this number as one of the ten speed dial numbers, enter a
digit from 0 to 9. If there is already a number in that speed dial
setting, it will overwrite the previously stored number without
warning. You will hear a confirmation tone indicating that the
number has been stored.
NOTE: When storing numbers into memory, if the handset is idle
(i.e., no key is pressed) for more than 30 seconds, it will beep rapidly, and the phone
will return to standby mode.
Dialing a Stored Number
1) When the phone is in standby mode, press the talk key, and listen for a dial tone.
2) Press the memory key and enter the speed dial entry (0-9) that has the stored number you
want to dial. (If you enter a digit that does not contain a stored number, the handset will
beep rapidly, and the phone will not dial.)

Nov 13, 2007 | Phones

1 Answer

CHANGE RINGER FROM HI TO LO


Do you know the model #? If so, you can get the owners manual from the the uniden website. Here is a link to the page so you can look for your specific model number. Just click on your model number and it will load the pdf format of the owners manual.

http://www.uniden.com/index/manuals_results.cfm?cat=1

Nov 10, 2007 | Uniden Cordless Phone

4 Answers

Emmerson Phone Manual EM2248


Emerson (EMSEM2646WH) I need to know how I can set up the speaker phone and in a way that will be clear and loud. I lost my manual, could you send another one to me?
thanks

Nov 05, 2007 | Emerson EMSEM2646WH Phone

1 Answer

Clear speed dial/one touch settings


There is no way to clear the settings you would have to re-program the correct setting. Did you program one touch speed dial on the line buttons? I do not see how programming a speed dial could effect accessing the CO lines unless you re-programmed the CO line buttons by mistake. If so, you would need to re-program those soft keys to line buttons. The manual you have may not cover this? The phone you have can work on a few different Panasonic phone systems. If you need a more detailed manual you will first need to know which Panasonic phone system you have. The phone part number WILL NOT help you determine which phone system you have. There is a main control unit somewhere (basement, utility closet, etc..)

Aug 13, 2007 | Panasonic KX-T7431 Corded Phone

Not finding what you are looking for?
Phones Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Phones Experts

kakima

Level 3 Expert

96518 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Cindy Wells

Level 3 Expert

4757 Answers

Are you a Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...