Question about Fastora NAS-T4 Hard Drive Array

Open Question

Password How to reset it .....I got a buddy gave me his Nas-T4 and I cant log in .....he dont remember password cause he stop using over a year ago. so is there a way to restore back to manufacture way? I tried to get the pdf manual but cant cause Fastora website does not exist anymore. Thank you moonwolf25@hotmail.com

Posted by on

3 Suggested Answers

  • 2 Answers

SOURCE: My Nas Fastora T4

I had the same problem after changing the disk setup from RAID-0 to RAID-5.

If you remove some of the harddisks (keep at least one) before booting, the system comes up again and is reachable for config changes.

I also had problems then with LAN1 card (did not get a ip address from DHCP anymore, only 0.0.0.0).
So I connected the Fastora NAS to LAN2. I was very surprised that the fastora filer tool did find the Fastora NAS connected with LAN2 configured to a wrong fixed IP-address that wouldn't work in my network. Fastora filer was able to remote change the IP-Settings for LAN2 card and now all works fine!

Hope this helps any other Fastora NAS user.

Posted on Jul 05, 2008

  • 2 Answers

SOURCE: Reading T4 Device

Did you try to boot the system without all the harddisks inside (keep at least one).
This helped me to bring up the NAS-T4 up again.

Posted on Jul 05, 2008

ktfacebook
  • 1 Answer

SOURCE: I picked up a Fastora NAS-T4, but the previous

Turn off the NAS.
Press AND HOLD power button for about 30 secs.
That will force a hard reset and reset the unit to factory defaults. You will lose all data on drives that are plugged in at the moment. If they are in an ejected state, it may save your data, but I have not tried that.

Posted on Jun 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset password


Log in to your NETGEAR router by browsing to
http://www.routerlogin.net/orhttp://www.routerlogin.com./
Enter the username (admin) and password. By default, the password is password or 1234 unless it has already been changed.
If you cannot log into your router:Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults.
however, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.
If it is not visible, you can change your wireless passphrase; however, changing the passphrase will cause you to lose your wireless connection.
Connect your computer to the router with an Ethernet cable before entering a new passphrase into the text box and Clicking Apply.
If there is a small hole in the front or back of the router push a hair pin in to reset to factory settings.

Sep 03, 2013 | NetGear ReadyNAS NV+ RND4000 NAS server...

1 Answer

Thermaltake N0001LNU Muse NAS-RAID 4 Bay drivers


Try ths driver solution out, it is the highest satifaction rating on the web. It helped fix most of my driver update issues and I still use it as part of my everyday work tool. It' s very useful and easy. Hope it helps you out.

Dec 02, 2011 | Fastora NAS-T4 Hard Drive Array

1 Answer

Windows vista is not detecting lacie network space 2 i am trying to install a lacie network space 2 (1T) on a home network. i use windows vista icw avg free virus software. i installed the latest...


In your office network, for sure, you have a DHCP server who gave the IP addresses to all devices for that network and this seems to be the reason for why you could see your NAS. On home, you also need a DHCP server. You don't say anything about you home network. The best idea is to just make a temporary network with 2 devices: your computer and your NAS by connecting the NAS directly to your computer's network adapter, set the IPV4 IP for that adapter to the same class addresses as your NAS was set by default (usually NAS had "192.168.x.y" where "x" could be 0, 1 or 2 "y" could be any value between 1 and 254, but mostly, 1) and try to access it via http to manage him (need a user name and a password). For NAS default address and username and password, consult NAS user manual. Access it with from your preferred browser using: \\192.168.x.y
Once you gain the control, cut off his DHCP service and tell him to accept the IP address from the network defined DHCP. (btw: one normal DHCP server is allowed on one network! Cascaded DHCP also is allowed, but it's a little bit complicated)
Good luck!

Jun 25, 2011 | LaCie Space 2 (301515EK) 1000 GB Network...

1 Answer

I picked up a Fastora NAS-T4, but the previous owner no longer recalls the root password on the device. Is there anyway to reset the device to factory defaults? I see no 'reset' buttons available on it.


Turn off the NAS.
Press AND HOLD power button for about 30 secs.
That will force a hard reset and reset the unit to factory defaults. You will lose all data on drives that are plugged in at the moment. If they are in an ejected state, it may save your data, but I have not tried that.

Oct 15, 2010 | Fastora NAS-T4 Hard Drive Array

1 Answer

Lost password of the administrator how to reset password?


hi

go to following link you will find your hard drive solution

http://www.laptoptips.ca/security/hard-disk-password/

Oct 07, 2010 | Maxtor MaxAttach NAS 3000 (A0801AA) 80 GB...

1 Answer

How do I configure it?


Use its ip address or its snap# to browse into it using Internet Explorer ( http://snap30123 ).The default log in is administrator and no password.
If the password is changed, hold down the reset button for 15 seconds and it shoud reset to default.

Jan 25, 2010 | Quantum Snap Server 4000 (5325301085) 30...

1 Answer

Reading T4 Device


Did you try to boot the system without all the harddisks inside (keep at least one).
This helped me to bring up the NAS-T4 up again.

Mar 04, 2008 | Fastora NAS-T4 Hard Drive Array

2 Answers

My Nas Fastora T4


There's a 9-pin serial connection on the back, can you use that connection to a terminal to see anything? Also, if you don't have access to the manual, visit this link to download the manuals: http://www.fastora.com/product_index.php?doc_name=nas-t4

Oct 22, 2006 | Fastora NAS-T4 Hard Drive Array

1 Answer

Reset root password


see http://www.intel.com/support/motherboards/server/ss4000-e/sb/CS-022318.htm for an answer

Nov 04, 2006 | Fastora NAS-104 (nas-104d) 0.25 GB Hard...

Not finding what you are looking for?
Fastora NAS-T4 Hard Drive Array Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fastora Network Storage Systems Experts

Geoff

Level 3 Expert

413 Answers

Brad Brown

Level 3 Expert

13512 Answers

Daily Mehdi
Daily Mehdi

Level 2 Expert

48 Answers

Are you a Fastora Network Storage System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...