Question about Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag6000aww valve wiering

I unplugged wiers and now can't remember witch ones go where, theres one plug with brown + blue ,and one organge and white, alsc one little plug (gray that used to go to a tempature meter that is now gone, think now it won't feel the heat and not work right after its hooked up with out gray ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Look for little abbreviations next to the spade connector
OR - orange
BK - black
BU - blue
BR - brown
they are usually marked and you should be able to figure it out

Posted on Sep 28, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Your cold water valve has failed and needs replacing, quite an easy fix. To get to it first unplug from wall, next remove water hoses from the machine, next lift the lid up and then just pull it off, next remove the two Phillips head screws at the of the rear of display console, lift off then unplug from motor controller, valves are now visible and are the parts which the water hoses where removed from, if they are blue in colour you will need to replace both hot and cold valves as the blue ones are a single unit but if they are white in colour you can replace the one that is not working as they are separate units. When removing the valves it will pay to cover the brown motor controller computer with a towel so as not to accidently get any water in it when removing as they do tend to hold a little abit inside. You can source parts from fisher & paykel you will need to quote the model number which is GW612 and the serial number aswell with that model as there can possibly be two types of valve available for that model, so keep them numbers handy when ringing them. Make sure you have display console fitted first aswell when putting it back together before fitting the water hoses just to make sure you don't accidently get any water on main computer board as this will kill it completely.

Apr 29, 2013 | Fisher and Paykel (IWL12)

1 Answer

I have just gone to replace motor controller on GW712 top loader washing machine but have found that the motor pump connections to be different. Old controller has 5 pin plug that does both, new...

The new motor controller board has a plastic breakout bit on the pump socket witch will give you 5 wire motor/pump.
No mod needed to wires or plugs.

Feb 17, 2012 | Fisher and Paykel Washing Machines

1 Answer

Makeing noise when washing

the best way is to take all the front cover out.
take the power plug out !!!
open the control panel, take the tow side plastic out from the left and right side and you see 2 screw to open.
take the control panel out disconect the plug and take out the 2 brass brakets from each side.
then pull the whole front cover out by tilting it to the front and pull it out.
you can see it on you tube on:

now take wire and bypass the plug you disconect from the controll panel 2 wiers need to be bypass dont bupass the ground wire!!!(green color)
now put the controll panel back down and you can run the machine with no front cove and see where the noize come from :)

Jan 19, 2011 | Kenmore 24032\24036 Top Load Washer

1 Answer

Ghw9100lw keeps throwing code f/h help

Unplug power cord. First try to clean drain tube by removing bottom cover: uncrew two bolts on each side. clean tube and filter and pump. If it is fixed, you are done.
If problem comes back, unplug power cord as always. Remove top cover and replace water inlet valve (remember to shut off water valves both hot and cold), unplug connectors to blue switch and remove water flowmeter, blow air thru one end and then the other end to remove dirt inside white water flowmeter. If flowmeter bad, replace it.
Last thing may get bad is pressure switch which is brow color valve on the right side of machine.
Good luck

Jul 17, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Washer comes on but does not fill. After a few seconds, 'LO' appears in window. Water shutoff valves are on. Washer operated correctly yesterday.

check to see if the water inlet 3 way valve is working right. there are 3-110 volt coils that should have a white, brown and blue connector. the white one usually supplies voltage first (depending on mode used). try a hot only load and see if the hot come in.

Mar 12, 2010 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Wire off around door

Nexxt 500 WFMC3301 Front Load Washer
This video will show you how to change a door seal on this Bosch front loader washing machine and the best way to get wier back on te door.
we have al bosch repairs in our channel

Please remember to subscribe to our YouTube channel for all appliance tutorials

a 4 THUMBS rating is appreciated for answering your FREE question.

May 13, 2009 | Bosch Nexxt 500 WFMC3301 Front Load Washer

1 Answer

My washer has a locking symbol on it , I once had a repair man to fix the same proplem , he pushed some buttons but now I cant remember witch one

Unplug the machine wait 10 seconds than plug the machine back in and press the cancel/stop button twice. this should unlock you washer and fix the problem. If this does not please give me the model number of your unit. it is located on the inside of the lid of your unit.

Jan 07, 2009 | Washing Machines

1 Answer

Washing machine

green and yellow is earth so wire the earth wire to this. brown is live in and blue is neutral in. brown/white is live out and blue/white is neutral out. usually a suppressor capacitor has a diagram printed on it

Oct 15, 2008 | Washing Machines

1 Answer

Flashing lights all across the front

it may just be the wiering harnes has worked loose also sometimes wires get caught and short out

Feb 06, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

PCB replacement

it seems that you are talking about the two wires that fit onto the back of the board where there is a black component that is square on the right hand side when looking from the front the wires fit within the black unit. i cannot remember which way around though. i will post again when i next do a wma repair ,tony.

May 22, 2007 | Hotpoint Aquarius WF000 Front Load Washer

Not finding what you are looking for?
Maytag Atlantis MAV6000 Top Load Washer Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4640 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides