Question about Dishwashers

1 Answer

Maytag dishwasher doesn't start - Dishwashers

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 943 Answers

Hi thanks for the question i would look at the door latch assy a very common problem with the Maytag dish washer thanks the appliance doc

Posted on Sep 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why doesn't it work?


Dishwasher Diagnostic Touchpad is Not Working,Maytag ...

? 8:28
https://www.youtube.com/watch?v=zex_g2TJRl4
Aug 6, 2013 - Uploaded by ApplianceVideo.com
Troubleshoot your Maytag Built-in Dishwasher which has this following issues: Touchpad System Is Not ...

Maytag Dishwasher Repair - Will Not Start or Complete a ...

? 5:06
https://www.youtube.com/watch?v=cfWUeh0ZtPY
Aug 9, 2013 - Uploaded by ApplianceVideo.com
Troubleshoot your trusty Maytag Built-in Dishwasher which has some of ... Dishwasher Diagnostic Touchpad is NotWorking,Maytag,Whirlpool ...

Top 638 Complaints and Reviews about Maytag Dishwashers

www.consumeraffairs.com > Homeowners > Dishwashers

Rating: 1.2 - ‎185 votes
Can't push a button to choose what cycle I want, it doesn't respond. .... After 2 1/2 years the control panel on my Maytag Dishwasher will not work. This is the 4th ...

Maytag Dishwashers - ConsumerAffairs.com

www.consumeraffairs.com > Homeowners > Dishwashers

Rating: 1.2 - ‎185 votes
My dishwasher just stopped working 1 year after purchase. .... Holding Control Lock or Delay for 3 seconds doesn't seem to clear the circuit board logic. Problem ...

Dec 12, 2015 | Maytag Dishwashers

1 Answer

Maytag MDB6000AWA doesn't fill with water


I had the same problem. Check and clean the sediment screen in the "water inlet valve". If this isn't plugged it is probably the solenoid on the same valve. I replaced the water inlet valve, took apart the inside apparatus of the dishwasher and gave it a good cleaning and this fixed the problem. The valve cost me $60.00CDN delivered to my door. You can order it online for as little as $30-$40.

Mike B.

Nov 09, 2011 | Maytag 24 in. MDB6600A Jetclean II...

1 Answer

Maytag dishwasher MDBH985AWS1 won't drain


Hi
Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. First make sure that the drain is not clogged and remove clogs if present. If no visible lint is present then remove the lower front access panel to check the drain filter and drain pump for any clogs, you'll need to clean the drain filter and drain pump completely. Also, check for any food pieces stuck near the pump impeller & clean the chopper assembly. Please note that dishwashers don't drain out the complete water such that heating element doesn't overheat. Hope this helps... Please post back for any further assistance.
Daniel

Jun 19, 2011 | Maytag Dishwasher

1 Answer

Own Maytag MDB5601AWW, serial 37004947LC - detergent dispener doesn't open


Hi,
There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....

Dishwasher Repair Problem Detergent Cup does not Open

heatman101 ';
';

May 10, 2011 | Maytag Dishwashers

1 Answer

Water is coming up through the kitchen sink when dishwasher is running and teh soap depenser will not release the soap.


Hi

Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn’t allow the door to open. The strip may not be getting 120V or maybe disconnected. Newer (plastic liner) Maytag dishwashers use a wax motor to open the soap dispenser. The plunger inside the wax motor slowly moves and pushes the plunger and door open. And, if this wax motor doesn’t receive 120 volts, then it’ll not work. Please check the voltage to the wax motor/Bi-metal strip, also inspect the connections to these. Please do rate this solution and revert for further assistance.

Daniel

Aug 14, 2010 | Maytag Dishwashers

1 Answer

Soap dispenser won't open during operation


Hi



Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn’t allow the door to open. The strip may not be getting 120V or maybe disconnected. Newer (plastic liner) Maytag dishwashers use a wax motor to open the soap dispenser. The plunger inside the wax motor slowly moves and pushes the plunger and door open. And, if this wax motor doesn’t receive 120 volts, then it’ll not work. Please check the voltage to the wax motor/Bi-metal strip, also inspect the connections to these.


Please do rate this solution and revert for further assistance.


Daniel

Aug 02, 2010 | Maytag Dishwashers

1 Answer

Dishwasher fix


something has gotten passed the screen and is jamming your pump impeller pull lower spray arm pull screen and see if you can find what is jamming the impeller and remove it drain pump is separate

Dec 30, 2007 | Maytag MDB7100AWB Dishwasher

1 Answer

Error e3?


i need your serial num its important 17

Apr 02, 2007 | Maytag 24 in. MDB5600A Jetclean II...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...