Question about Draytek Computers & Internet

1 Answer

Vigor2910vg locked intoTFTP mode

Executing firmware update,99.99% complete then received a timeout error. ACT & DMZ led's flashing. cannot do anything with the box and PC doesn't seem to see the router at the default address.
How can I clean the slate and start over?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 35 Answers

Try to Hard reset the router before executing firmware update.

Press reset button and hold it for 1min. You to turn off the router and turn it on before updating the firmware.


Goodluck!!

Posted on Oct 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HP Designjet 500 has a locked screen. I have been trying to get the plotter to run on our new computer and it locked up after installing the current Firmware and driver updates. Any suggestions would be...


Dear Friend, It's a serious issue what I understood & confusion is control panel locking facility not avail in this model, how its locked?.. Simple method to catch the faulty part through power LED behaving s..(Power led located on power button)

# LED is OFF - This indicates that the Power Supply Unit is
completely dead. Try the following:
1 Check that power cord is connected correctly to the Printer and to the Power Socket.
2 Replace the Power Supply Unit
# LED is ON (all the time) - This indicates that the Main PCA is completely dead. Replace the Electronics Module
# LED is Flashing - A problem has been detected with the previous firmware upgrade. Try re-send the firmware upgrade file.
# LED Flashes twice every few seconds - The Printer cannot detect the Interconnect Cable. Try the following:
1 Check that the Interconnect Cable is connected correctly to the inter connector PCB & Electronic module.
2 If the Interconnect cable is connected correctly and the LED continues to flash twice then replace the Interconnect Cable
LED Flashes 3 times every few seconds - The Printer cannot
detect the Front Panel. Try the following:
1 Check that the Front Panel is connected correctly to the Interconnect PCA.
2 If the Front Panel is connected correctly and the LED continues to flash 3 times then replace the Front Panel
LED Flashes 4 times every few seconds - This indicates that the Electronics Module has failed. Replace the Electronics Module
LED Flashes 5 times every few seconds - This indicates that the Electronics Module has failed. Replace the Electronics Module.
Now U decide that whether firmware uploaded properly or not?..if not its sure that Electronic module gone.. you have 2 replace it..
Any further help/query pl reply, best of luck..

Oct 02, 2013 | HP DesignJet Office Equipment & Supplies

2 Answers

WHAT LIGHTS ON LINKSYS ARE SUPPOSED TO BE BLINKING


Note that incoming traffic will cause the WAN (or Internet) light to blink even if it is 'probe' traffic trying to break in to your network. Such traffic is to be expected and is the reason you have firewall functionality in your gateway router.

On the inside, there is a bit of traffic on any LAN when the computers are turned on. Messages generated by the router itself are used to find computers and printers for a lot of different legitimate reasons.

Feb 25, 2013 | Linksys Wireless-G WRT54G Router

1 Answer

Hp cm1312nfi printer problem error ready to download


The error is due to corrupt firmware and you need to reinstall it.
HP CM1312NFI Firmware Download & Instructions
Please visit the above link and Download the firmware.
"The HP Easy Firmware Upgrade utility provides the HP MFP firmware .rfu bundle and a user friendly method to transfer the .rfu file to the MFP all contained in a self-extracting executable for the Windows operating systems"

Please visit the above link and read all the instructions/ details and upgrade the firmware.
Process:
  1. Download the flash firmware updater file from HP.com to the PC desktop.
  2. Turn the printer off and then back on to clear main printer memory.
  3. Double click on the flash firmware update utility file. An HP firmware update window will open.
  4. Select the appropriate MFP in the dialog window. If you assigned a different name to the HP MFP, choose the name that represents the correct printer.
  5. Click on "Send Firmware" when ready to proceed.
  6. The progress bar will begin to move to the right indicating information being transferred.
  7. DO NOT power cycle the product or the pc during this process or the product may become unstable and or unusable without further attention from HP. The flash firmware update can take up to 5 minutes to complete. Please be patient.
  8. During the product flash firmware update, the display on the product control panel will display "Erasing - Programming - Complete - Hewlett-Packard - Ready - Initializing - Ready". Once the download is finished the printer will be in the Ready state.
  9. At the conclusion of the firmware update, the dialog window will show a smiley face. Click on exit.
  10. The flash firmware update process is complete.
Let me know if any further clarification/ assistance is required.

Hope it helps! Good Luck! Thanks for using Fixya!
CreativeTECH

Jun 09, 2011 | HP LaserJet CM1312 All-In-One Printer

1 Answer

HP M2727nf laserjet.Firmware courrpt on display .printer locked up


The error is due to corrupt firmware and you need to reinstall it.
HP M2727NFFirmware & Instructions
Please visit the above link and Download the firmware.
"The HP Easy Firmware Upgrade utility provides the HP MFP firmware .rfu bundle and a user friendly method to transfer the .rfu file to the MFP all contained in a self-extracting executable for the Windows operating systems"

Please visit the above link and read all the instructions/ details and upgrade the firmware.

Extract of the instructions for Firmware Update from Hp Official Site is as under: -
Process:
  1. Download the flash firmware updater file from HP.com to the PC desktop.
  2. Turn the printer off and then back on to clear main printer memory.
  3. Double click on the M1522_MFP_Series_FW_Update-20100902.exe. An HP firmware update window will open.
  4. Select the appropriate MFP in the dialog window. If you assigned a different name to the HP MFP, choose the name that represents the correct printer.
  5. Click on "Send Firmware" when ready to proceed.
  6. The progress bar will begin to move to the right indicating information being transferred.
  7. DO NOT power cycle the product or the PC during this process or the product may become unstable and or unusable without further attention from HP. The flash firmware update can take up to 5 minutes to complete. Please be patient.
  8. During the product flash firmware update, the display on the product control panel will display "Erasing - Programming - Complete - Hewlett-Packard - Ready - Initializing - Ready". Once the download is finished the printer will be in the Ready state.
  9. At the conclusion of the firmware update, the dialog window will show a smiley face. Click on exit.
  10. The flash firmware update process is complete.
  11. If it is desired to verify the update, use the control panel reports menu under setup to print a configuration report. The configuration report will show the current firmware revision in the Product information block, Firmware Datecode: 20100902.
Hope it helps! Good Luck! Thanks for using Fixya!
CreativeTECH

Jun 03, 2011 | HP Office Equipment & Supplies

1 Answer

No wireless connection for laptop. Linksys router - model #wrt160n v2


you can run a direct line to that router and go to the cisco web site and get the information you need to run that router. its a pdf format and is 2.56 Meg. Try this

SecureEasySetup (Orange/White) The Cisco logo is the Router's SecureEasySetup button. It

lights up and will stay orange when the Router is powered on. The color orange indicates that

the Router is not using the SecureEasySetup feature, while the color white indicates that the

Router is using the SecureEasySetup feature. When the Router enters SecureEasySetup

mode, the Cisco logo will turn white and start flashing. After the Router has generated

the SSID and WPA Personal key, the Cisco logo will stop flashing and stay white.

To clear the SSID and WPA Personal key, press and hold down the Cisco logo for five seconds.

The Cisco logo will flash slowly as the Router resets itself. The Cisco logo will turn orange to

indicate a successful reset.NOTE: SecureEasySetup is a feature that makes

it easy to set up your wireless network. If you have SecureEasySetup devices, run the Router's

Setup Wizard CD-ROM and follow the onscreen instructions to use SecureEasySetup.

Power (Green) The Power LED lights up and will stay on while the Router is powered

on. When the Router goes through its selfdiagnostic mode during every boot-up, this

LED will flash. When the diagnostic is complete, the LED will be solidly lit.

DMZ (Green) The DMZ LED indicates when the DMZ function is being used. This LED will

remain lit as long as DMZ is enabled. WLAN (Green) The WLAN LED lights up when

the wireless feature is enabled. If the LED is flashing, the Router is actively sending or

receiving data over the network. 1, 2, 3, 4 (Green) These numbered LEDs, corresponding with the numbered ports on the Router's back panel, serve two purposes. If the LED is continuously lit, the Router is successfully connected to a device through that port. A flashing LED indicates network activity over that port.

Internet (Green) The Internet LED lights up when there is a connection made through the

Internet port. A flashing LED indicates network activity over the Internet port.

Good luck

Nov 26, 2010 | Computers & Internet

1 Answer

One light is out on my linksys usb200m


It depends on which light is OFF: Below are the LED indicators:

100/ACT Green. The LED lights up when there is a connection to a 100Mbps network. It flashes when the computer is transmitting or receiving data at 100Mbps.

F/H Green. The LED lights up when the Adapter is operating in fullduplex mode. The LED is off when the Adapter is operating in half-duplex mode.

10/ACT Green. The LED lights up when there is a connection to a 10Mbps network. It flashes when the computer is transmitting or receiving data at 10Mbps.

Dec 04, 2009 | Linksys USB200M USB 2.0 Network Adapter

1 Answer

Error 79 ...shuts off and the screen says error 79


Hi angelahender:
Here is your problem.
79 Error
PowerOff>PowerOn
The product has experienced an
internal firmware error.
Disconnect the power cable from the
product, wait at least 30 seconds, then
reconnect the power cable and wait for
the product to initialize.
If the error persists, upgrade the firmware.
Firmware update via flash executable
The configuration page lists the firmware version of the product. On
flash-memory-based products, you can update the firmware code by
downloading the latest flash executable for the product and running
the program according to the readme instructions that come with it. If
the firmware should become corrupted or fail (usually because of an
interruption when attempting to update the firmware), the product will
no longer function. In this case, a firmware recovery DIMM is
available from HP.

Hope this helps



Jul 16, 2009 | HP LaserJet 3330 All-In-One Printer

1 Answer

We are getting a F9-00 code. how do we solve that problem?


F9-00 is a timeout between the main and imaging boards in your machine. If this is a one-time occurrence you can power off and power on. If it reocuurs you can go into test mode and clear the error with SIM 14 (key sequence P-*-C-* ... then 14-Start-Execute-Yes and hit CA to reboot).

Some things you can do to keep this from happening:

Get your copier on it's own outlet and share it with nothing else.

Put a filter on the line to block out RF interference.

Try turning the copier off, unplugging the network cable, turing it on, waiting until it's ready, then plug the network cable in.

If your F9-00 still comes back, your copier may need a firmware flash. For this model, that procedure is extremely obnoxious and best handled by a service tech. I just wrote a 6-page how-to and I am still adding to it.....

Jun 30, 2009 | Sharp AR-BC320 All-In-One Led Printer

1 Answer

My colour printouts from new Samsung CLP-310 do not match original WORD 2000 docs colours (or compared to HP deskjet. Is there a MS patch for this?


Hello,

There is an update for your printer. This is a firmware update. A firmware update, rewrites code located on the printer's main system board. The latest update is dated 10/17/08.

Flashing firmware does not have a go back element or undo, so it is really important that we verify your model and what seiries of printer you have. I suspect you have a CLP-300 Series printer and that the 310 of the 300 just describes some features added or left off and even who you purchased it from, in many cases.

Please look at these two photos and then post the data off the name plate for your model number in particular.

406eb47.jpg ccb435d.jpg

You will notice there are two lines to include in your reply.
1.) The Model: (first line)
2.) M/C entry (second to last entry in this photo of the label.

Once you verify this and I post the firmware update link for you, you will need to follow the instructions I include below.

Regards,
Worldvet


[from Samsung.com PDF file on this firmware upgrade]

Samsung has released a new Software upgrade file for print quality, automatic error recovery, and toner save mode on color laser printers.

Procedure to Set-up Download Mode on Your Printer - CLP-300 series
Turn power off.
While holding down the ‘STOP’ button on the Printer, turn the Printer back on.
Keep holding down the ‘STOP’ button until all the LEDs turn orange.
Then release the ‘STOP’ button, and press it again, one more time.

1. How to Upgrade
Please make sure to check the printer model number before performing the firmware upgrade.
2. Release Notes
Improved on light printing quality at low temperature environment
Automatic error recovery at abnormal operation
Toner save mode by optimized toner supplying
3. Caution
After firmware upgrade is completed, green LED lights will light up.
Do not turn off the printer before green LED lights turns on. A power interruption will corrupt the process.
If the printer is connected by a USB cable, disconnect all other USB devices, except your keyboard & mouse, from the computer.
If possible, be certain the Printer is connected to a BackUPS

Firmware Update Confirmation Instruction
Model CLP-300 series
When firmware upgrade is started, status LED light will start blinking.
As the printer reinitializes, status LED light will automatically turn off and then on.
Firmware upgrade is complete when status LED stays on green.

After firmware upgrade is completed, the LCD will display the message ‘Ready Copy’ and the LEDs will stay on green.

4. If there is an Error after firmware upgrade
If LED is on red or blinking after firmware upgrade, set-up download mode again and re-try the firmware upgrade.

Oct 20, 2008 | Office Equipment & Supplies

1 Answer

Firmware Update Fails


I'm not sure this will help, but per Magellan (see below), the firmware update must be run twice as your firmware is earlier than version 3. I have a GPS 315 with v2.03 and can't find a cable to update mine. My GPS 315 does not appear to have a cable connection either, just a screw port on the back for a carrying strap. Was your homemade cable wireless? How did you make it?

You must follow instructions exactly to avoid corrupting your unit's flash memory.
  1. Select the .zip file and save it to your hard drive. Open the .zip file using WinZip.
  2. Connect your receiver to your PC using the PC or Power/Data Cable.
  3. Turn on the receiver and press the NAV key.
  4. Make sure the batteries are at least 50% full.
  5. Select the MAGUP executable file from your PC.
  6. Follow the instruction until you see the message Upload Complete.
  7. If your unit's software version is earlier than 3.00, you will be prompted to turn the unit on again and load the software a second time. Follow the instructions.

Jul 19, 2008 | Magellan GPS 315 GPS Receiver

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Draytek Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

101437 Answers

David Payne
David Payne

Level 3 Expert

14160 Answers

Are you a Draytek Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...