Question about Lexmark X342n All-In-One Laser Printer

2 Answers

Lexmark X342n Exception:ABT when booting up.

When my Lexmark X342n boots up, it goes into performing self test and right after I get the following message: Exception: ABT on the first line and the second line scrolls stuff like : r9: 0X00000000 . All the buttons are inactive. Can't select or do anything at all. Any ideas????

Posted by on

  • 1 more comment 
  • Quitec Mar 28, 2009

    Lexmark X342n Exception ABT
    I can´t solve this problem with a Lexmark X342n. When it starts this messege appear and I don´t know why?
    Please Help!!!


  • Anonymous Apr 02, 2009

    lexmark x340 exception abt

  • muhamedhayek May 11, 2010

    Lexmark X342n Exception:ABT erro

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,602 Answers

GO ON LINE TO CANON AND TYPE ON LINE OR ADDRESS BAR

CANON X342N BOOT UP ISSUES
OR
CANON X342N EROR MESSWAGE R9:0X000000000
OR
CANON X342N FREEZES AFTER IT STARTS

I THINK YOU WILL FIND WHAT YOU ARE LOOKING FOR BUT IF NOT YOU CAN CONTACT ME AGAIN

ROD IS THE CANDYMANGANDY

Posted on Feb 04, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 320 Answers

If the printer is running script in the window i would say that it has suffered damage to the nvram chip on rip logic board. lexmark has no information on your error. i work on these pretty regular and have not seen this error myself i do see alot of errors created by the printer taking a power surge that there is no record of

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

8560 printer shut itself down and will not true back on


The following lists the chain of events that occur when you turn on a printer. You can follow this list as one means of determining if the printer is operating correctly. The exact chain of events depends upon the last power down condition and where the printer has last determined the printhead is positioned, this is stored in non-volatile RAM. The Checklist is the primary reference for troubleshooting power-up problems.

1. Power cord is plugged in and the power switch is turned on:

2. Power supply senses AC line voltage conditions (110 VAC or 220 VAC)

and enables DC voltages. If an overload occurs, the printer turns off the high voltage DC supplies, causing a "blink" effect on the Control Panel LEDs.

3. BIST test flashes the PE LED very briefly at a fast rate until the end of the

next test.

4. The Boot loader performs CPU initialization and RAM test. It then sends

the boot loader version to the serial port.

5. Power-On Self Test (POST) initializes the Control Panel. The Control

Panel LED turns red, green, orange, and then off. The Control Panel LCD then goes black and then clear. The POST version displays on the LCD

and waits two seconds. During this time the operator can press the Back

button to bypass the remaining POST test.

6. Low level Power-On Self Test (POST) diagnostics are performed. The

Control Panel displays status messages as each sub-test is performed.

This test takes about 8 seconds. All LEDs are off during the test.

If POST diagnostics pass, the Control Panel displays the Xerox logo and turns on the green LED.

If the test detects an error, the error message displays on the LCD and the printer flashes the LEDs with a repeating error code pattern.

7. The VxWorks operating system is initialized and engine code is started.

This takes about 15 seconds. The Xerox logo is displayed.

8. Print Engine Self Test (PEST) diagnostics are then performed. These test

the heaters, clutches, motors and solenoids. As each clutch is tested, you hear clicking with four high tones as each motor is tested. This test takes about 30 seconds.

9. The printer now runs the mechanical initialization. The exact sequence
depends on the initial position of the printhead and wiper assembly.

Feb 28, 2014 | Xerox Phaser 8560MFP Laser Printer

1 Answer

8560 shut down and will not turn back on


The following lists the chain of events that occur when you turn on a printer.

You can follow this list as one means of determining if the printer is operating correctly. The exact chain of events depends upon the last power down condition and where the printer has last determined the printhead is positioned, this is stored in non-volatile RAM.


1. Power cord is plugged in and the power switch is turned on:

2. Power supply senses AC line voltage conditions (110 VAC or 220 VAC)

and enables DC voltages. If an overload occurs, the printer turns off the high voltage DC supplies, causing a "blink" effect on the Control Panel LEDs.

3. BIST test flashes the PE LED very briefly at a fast rate until the end of the

next test.

4. The Boot loader performs CPU initialization and RAM test. It then sends

the boot loader version to the serial port.

5. Power-On Self Test (POST) initializes the Control Panel. The Control

Panel LED turns red, green, orange, and then off. The Control Panel LCD then goes black and then clear. The POST version displays on the LCD and waits two seconds.

During this time the operator can press the Back button to bypass the remaining POST test.




6. Low level Power-On Self Test (POST) diagnostics are performed. The



Control Panel displays status messages as each sub-test is performed. This test takes about 8 seconds. All LEDs are off during the test. If POST diagnostics pass, the Control Panel displays the Xerox logo and turns on the green LED.

If the test detects an error, the error message displays on the LCD and the printer flashes the LEDs with a repeating error code pattern.

7. The VxWorks operating system is initialized and engine code is started.

This takes about 15 seconds. The Xerox logo is displayed.

8. Print Engine Self Test (PEST) diagnostics are then performed. These test

the heaters, clutches, motors and solenoids. As each clutch is tested, you hear clicking with four high tones as each motor is tested. This test takes about 30 seconds.




Feb 28, 2014 | Xerox Phaser 8560MFP Laser Printer

1 Answer

Manual for lexmark x342n


Free download of Lexmark X342N User Manual. www.retrevo.com/support/Lexmark-X342N-Multifunction-Printers-manual/id/391ci154/t/2/ www.retrevo.com/support/Lexmark-X342N-Multifunction-Printers-manual/id/391ci154/t/2/ Lexmark X215 MFP User's Guide

Have checked this site and it has the doc you require - hope this helps

Feb 01, 2012 | Printers & Copiers

1 Answer

LEXMARK X342n error code 202.13


The exit sensor at the fuser is activated by a piece of media indicating. There is a piece of media in the machine during POST (Power-On Self Test).


Check for media in the exit of the fuser assembly or redrive assembly. Feed a sheet of paper, and if the same error occurs after clearing the fuser or the same error occurs when no media is present, check the exit sensor assembly.


For further assistance, please contact Lexmark Technical Support.

Apr 11, 2011 | Lexmark X342n All-In-One Laser Printer

2 Answers

My faxes are not printing. They seem to be connecting but they won't print.


Tips and tricks For the LEXMARK X342N


1) Faxes won't print.

Try this first....
Press <MENU> then <*> <#> on the keypad
Press <UP ARROW> and see "UTILITIES RESET SYSTEM"
Press <CHECK MARK>
and see RESET SYSTEM
Press <DOWN ARROW> and see (FAX NVRAM)
Press
<CHECK MARK> should reset the fax memory.

Try this second....
Press <MENU> then <*> <#> on the keypad and see "SERIAL NUMBER"
Press <UP ARROW> and see "UTILITIES RESET SYSTEM"
Press <CHECK MARK>
and see RESET SYSTEM
Press <DOWN ARROW>
<DOWN ARROW> <DOWN ARROW> and see (ERASE FFS)
Press
<CHECK MARK> should reformat the fax memory.
It will reboot. Occasionally says the FAX NVRAM is bad
when performing the boot-up self-test and corrects the problem.

2) PC LIFE WARNING message
After replacing your photo conductor kit you need to reset the "PC LIFE WARNING" message. With the front toner door open press and hold the red <STOP> until you see the "RESETTING PC COUNTER" message


Mar 15, 2010 | Lexmark X342n All-In-One Laser Printer

1 Answer

Lexmark342n is stuck on self test what do I do.


Hi Derek, I have experienced similar problems with the printer. Try unplugging it from the power as well as the computer and wait for a couple of minutes and then re-plug; should restart, worth a try anyway. Good luck from Marion

Jan 02, 2010 | Lexmark X342n All-In-One Laser Printer

2 Answers

How do you remove the 80 maintenace maeassage after the kit has been replace??


It should do it automatically. If not run the check system. If you have done that try the clean head setting and print to see if you are clear.

Nov 06, 2009 | Lexmark T644 Laser Printer

1 Answer

Lexmark x342n Printer Driver


Please go to www.lexmark.com. Then select drivers and download. Put the printer model number into the first search bar and then find the correct driver for the operating system that you have. Don

Apr 16, 2009 | Lexmark X342n All-In-One Laser Printer

Not finding what you are looking for?
Lexmark X342n All-In-One Laser Printer Logo

1,945 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...