Question about Emerson EWF2704 TV

1 Answer

Direct TV remote does not control TV on/off or volume.

Must use two remotes to watch TV. There are no codes to program the Direct TV remote to control Emerson TV on/off or volume.

Posted by on

  • 1 more comment 
  • spettigrew1 Oct 06, 2008

    We have the same problem.  We just upgraded to a DVR under Direct T.V., unfortunately.  We now have to use two remotes because there is no code for Emerson.  The technician supposedly tried every code he knew of and still couldn't get the remote program.  Why is this?

  • Anonymous Nov 28, 2008

    We have the same problem. We have been putting codes after codes in and nothing has worked. Ours is the Emerson BLC329EM9

  • Anonymous Dec 17, 2008

    I just found this forum because I have the same problem with my emerson Tv. I tried every code and it still won't work

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have some codes hope they will help. slid remote to tv and hold away from tv as u push mute and select till light blinks twice. then point at tv and try these. 10154-10236-10463-10178-10171-101179 good luck

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do I switch the Input Select to watch a movie when the button doen't work?


I recommend getting a universal remote to replace your tv remote.

Apr 28, 2014 | Symphonic ST420FF 20" TV

1 Answer

Hi. Can you please tell me the correct code for the Curtis tv for Cablevision Remote? We have two remotes now, the cable remote cannot operate the volume or the power on/off tv, must use Curtis remote.....


Hello
Codes for Curtis TV with Cablevison remote control are:-

070 004 101 127 236 011 072 081 120 164

*Tip: The iO button will light on for 20 seconds. The

next step must be entered while the iO button is
on.

STEP2 Press the [INFO] button.

The iO button will blink number of times indicating the

number of each digit of the code number. Each digit is

separated by a 1 second interval of the iO button being

turned off.

Example :One blink, three blinks and eight blinks with

an interval of 1 second of iO button being

turned off, indicates the code number 138.


Note :Ten blinks is equal to the number 0.


D. Program the Volume Controls.

By following the steps below, the user can program

the volume controls (Volume UP, Volume Down and

MUTE) . The default volume control settings on the

remote control is TV volume control. If you wish you

can control the volume via your CABLE box, use the

following steps.

STEP1 Press the [CBL] button and the [SEL] button

simultaneously for 3 seconds. The iO button

will turn on.

*Tip : The iO button will light on for 20 seconds.

The next step must be entered while the

iO button is on.

STEP2 Press the [VOL +] button.

STEP3 Press the [CBL] button.

The iO button will blink twice to confirm the

programming.

To return to original state:

If you wish you can control the volume via your TV,
repeat the above steps by pressing [TV] in STEP3 .
OK.

Dec 23, 2010 | Curtis CM13102 13" TV

1 Answer

I can't get my dish system to work with this TV. I'm only getting 2 chanels. How do I program new chanels to this TV? I need chanel 60.


It depends on the TV a bit. Which model of Broksonic TV do you have? Do you have the original remote? (remotes.com has replacement remotes for many TVs.) Look at the TV (or the original remote) for a menu or channel add subtract option. (The TV is probably programmed to skip the channels that didn't have a signal in the past so you need to reprogram this.) If the TV is a really simple TV (with just the channel and volume controls on the TV), you'll need the original or a direct substitute remote (or a higher end programmable remote). Most basic universal remotes will control power, channel and volume but not the reprogram channels option (in my experience). If you can program the add/remove channels, press 60 on the remote, wait for the TV to go to that channel and then press the Add Channel button. Alternately, with the satellite receiver on, press the combination to search all channels and program the skip to channels with signal.

I hope this helps.

Cindy Wells
(I had a really old Emerson TV; when the original remote started to fail, the cheap universal remote didn't handle the channel programming. Fortunately, the original remote would usually still work for that.)

Jul 07, 2010 | Broksonic TV

1 Answer

I have a APEX AT3208S 32" TV and I just subscribed to Direct TV, when I programmed my remote to the Direct TV, i have to use 2 remotes, one to turn the tv on and go to Video 3 and the other to switch...


The direct tv remote will control all of your electroincs set that one up for all of your needs ...codes for tvs in the direct tv book! make sure you change the selection on the remote!

Dec 06, 2008 | Apex Digital AT3208S 32" TV

4 Answers

Curtis Mathes TV Remote Control Codes for Programming the remote to the TV


I own a One-for-All universal remote, and my booklet says the setup code for a Curtis Mathes TV (without a built-in DVD or VCR) is one of the following numbers: 0030, 0047, 0054, 0060, 0093, 0145, 0154, 0166, 0451, 0702. I can not guarantee these numbers will work with your remote, but it is worth a try.

Jul 03, 2008 | Curtis-Mathis CM32010 TV

1 Answer

32" proscan dual hd tv can't get universal or direct tv remote to work what now


Get a universal from big box and program. If you can find a rca remote, it should be programmed already.
Craig www.classtorations.com

Jun 08, 2008 | Proscan PS32500 32" TV

3 Answers

Remote control code needed for this TV


Need to program my Insignia TV to my Direct TV remote. Need code

Nov 07, 2007 | Insignia IS 20" TV040919 TV

3 Answers

Whats the tv remote code if i have a direct tv + remote.


The Directv remote isn't capable of fully emulating the native remote of the Symphonic Combo. You can get limited functionality though.

1. Move Remote slider to "AV1" position.
2. Hold down mute and select until you get 2 flashes of the green light, then release both keys.
3. Enter 20821 and observe 2 more flashes of the green light.

Next lock the volume controls to this device.

4. If you have moved the remote's slider from the AV1 position, move it back. The slider should remain on AV1.
5. Hold down mute and select until you get 2 flashes then release both keys.
6. Enter 993 and observe 2 flashes.
7. Press and release THE SELECT KEY and observe 2 more flashes.

You can control the TV's power using the big power button under the device selector.

Oct 23, 2007 | Symphonic WF20D4 TV

Not finding what you are looking for?
Emerson EWF2704 TV Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Emerson Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68301 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Are you an Emerson Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...