Warings lights coming on, SLIP indicator,CHECK indicator, VSC OFF indicator,comes on.

what were the code numbers you gave me code c1336 This means there is a zero point calibration code unfone. So you need a zero point calibration needs to be reset with a scan tool.

I currently have the same issue on my 2008 Tundra. I have noticed that one of the 12v acces plugs don't work. The problem is intermittent and started when the air was damp or after it rained. Now the same lights are on, the 12v doesn't work and the remote door locks don't work. Toyota want to run a diagnostic check at $125 an hour. Did you solve your problem?

Hello, these lights being on indicate a fault that affect both vehicle stability control and engine performance. In some cases, it could be a transmission related concern, but not in all.

However this can be very helpful

Make sure you are completely stopped. Put the car in park if you can.
Press and hold the VSC button for a few seconds.
The TRAC OFF and VSC OFF indicator light will come on. Both systems are now off.
Press the VSC button again. Both lights will turn off and the systems are now reengaged.

You can also check this out if you are having any problems with your smart key

Go to a major auto parts store and ask for them to read out your diagnostic trouble codes. They will usually do that for free. When the check engine light comes on, the car's computer has trouble codes that are waiting in memory to be read by a code reader. Most major auto parts stores have a code reader--ready and waiting to help customers find out what is wrong. Write back here with your codes and we can help you too!

You need a scanner to pull out the engine light codes.
Use a shopu manual to aid you with the diagnosis and repair.
The slip indicator and vsc light being on means these systems are not working. Once you pull the codes and do the repair and erase the codes the lights will go off.
There will be a code in there for the misfiring.
Good luck and keep me posted.

VSC is Vehicle Stability Control. This is and electronic sensing which monitors and combines performance of braking, wheel slippage and handling, ect.
If this light comes on along with check engine light, it can be caused by a loose gas cap or faulty o2 sensor.

VSC is Vehicle Skid Control. The system is usually on, but when you turn it off (on my mother's 01 Avalon, it's on the knee bolster, below and to the right of the steering column), the indicator comes on in the cluster to let you know it's turned off - it's just a reminder to you that you don't have that safety net activated. The way the car is set up, even if you turn it off, when you shut down the engine and then restart it later, the system is rearmed automatically.

What I'm thinking is, since you've obviously had the engine on and off and the VSC OFF and TC OFF warnings are still illuminated, you probably have a problem with either an ABS sensor, a yaw sensor, or something related to those, as those systems rely on a bunch of sensors to work. If they have failed, it should illuminate the check-engine light. Stop at Auto Zone or Advance Auto Parts and have them scan the car's computer (it's free). They'll give you a list of the fault codes that come up. If you post them up here, I can define them for you and help you solve the problem - just post them as a reply or follow-up on this posting.

generally when a landcruiser doesthat it is because the alternator is on the way out -----get checked out by an auto electrician

On a Prius, when the check engine light comes on it indicates a malfunction in the powertrain control system. You need to have the car scanned for codes to see where the fault lies. The red triangle lights because the check engine light is on. The VSC is disabled when the check engine light is on and that light comes on.
Start with having the car scanned.

If just found this on another forum:

A few days ago I started the Cruiser and had 4 indicators stay lit.
They were the CHECK ENGINE...SLIP INDICATOR..VSC TRAC..VSC OFF.
Didnt noticed any change in driving and 4-wheel drive is still working.
I removed the negative cable from the battery and the same indicator lights have NOT come back. Everything is back to normal as far as warning lights go. Should I take it in to the service center and have it checked.
Or should I wait to take it in, if it does it again?