Question about Computers & Internet

1 Answer

When I put it in the computer nothing happens. Do I to pull something up myself?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.

  • Expert
  • 60 Answers

You could go to my computer and click on the drive that has the cd in it and it should start up.

Posted on Sep 25, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

After installing a rebuildt transmission itwill not engage any gear did i hook up something wrong

Hey Scott,
did you check fluid level? if the torque converter was dry it'll suck up all the fluid when the 'pan' reads full check fuses,trace wire harness for damage during installation. good luck

Feb 08, 2015 | Cars & Trucks

1 Answer

Power switch

check your connections..chances are you missed something

Jan 08, 2014 | Compaq Presario CQ62-215DX Laptop

1 Answer

Hi I recently got myself a Acer Emachines Em350 nav51 but the touchpad/trackpad will not work. I have tried using fn+F7 to active it but nothing happens. Tried diffent drivers as well with no...

Maybe go to the device manager in control panel and click on Device Manager look for the HID Compliant mouse or touch pad and un-install the driver completely after that restart your computer as soon as it boots up it will find new hardware and take you through the setup process most computers does this for you after it says installation complete try the touch pad if nothing happens try pressing the Fn keeping it down press the F7 button then release them both if still nothing happens then it will be your motherboard as it will required going back to them under their warranty to be fixed.

Jun 27, 2011 | E-Machines emachines (emachinees) CD-ROM...

1 Answer

My computer has my printer installed but it won't print. Everytime I try to print something, my computer says it's printing, but nothings happening. What do I do? Is my printer messed up or is it my...

Yes! Windows will connect to the printer as soon as it sees it, but the software it puts in is useless. You should have left the printer disconnected, put in the Install CD that came with the printer and only connected when the Install program asked you to. NOW, delete the printer, reboot the PC with the printer disconnected and follow the procedure I have just described. It WILL work. I know because I have the same printer and have made this mistake myself! Good Luck, Ian.

Jun 14, 2010 | Lexmark P3150 All-In-One InkJet Printer

1 Answer

I'm not sure how to use my micro sd card, i put it...

Nothing, when you put it in it should appear in My Computer if it's in working order.

May 17, 2010 | Computers & Internet

1 Answer

HP pcs 1610 won't print words. Prints symbols instead.

Try creating the document on another program. If that does not work try to find software from another site HP should have all the software and updates on a current download file. You should not have interference with the download, if so there may be a quirk in your computer somewhere.

Aug 20, 2009 | Office Equipment & Supplies

1 Answer

2000 Acura TL- Window won't go down in rear seat on driver side

It sounds like the cable has pulled off a pulley. You probably need a regulator, if you hear something every time you push it, then the motor may be fine. Take the interior panel off, make sure to look for hidden screws :>) and check regulator. You can do it if you take your time :>)

Jun 28, 2009 | 1991 Honda Accord

1 Answer

System turns on however hard drive will not cycle nor will mouse or key board activate

Turn power off and unplug power from computer.
Unplug printers,backup drives and speakers.
Open case and unplug power supply from the board.
plug power cord back in press the power button.
Of course nothing will happen.
unplug power cord again.
plug power supply back into the board.
plug power cord backup and press power switch.
If nothing happens unplug power cord again.
pull out your memory sticks and plug cord back in and press power button.
Of course not much will happen.
But really something is happening to your computer so continue.
Pull power cord and replace memory sticks.
replace power cord and press power switch.
Continue this pulling out pci cards one at a time until you find out what the problem might be.
Try different keyboards and mice too.
Good Luck

Oct 27, 2008 | Intel Computers & Internet

1 Answer


you need to replace the light engine. There is a problem with tunnel.

Jul 11, 2008 | Toshiba 56HM66 56" Projection HDTV

2 Answers

Canon zr45 wont record


Jul 27, 2007 | Canon ZR45MC Mini DV Digital Camcorder

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides