When I punch the code to unlock the keyless entry there is a steady beeping

Hello Cathy

It does indeed have keyless entry. It needs reprogramming when you get a new remote. Also if you disconnect the battery. Usually a local car alarm fitting shop, or an auto-electrician will do it. Plus of course a Ford dealership.

https://www.google.com/search?q=Keyless+Entry+Remote+System+1999+Ford+Windstar

..

Remove the battery and have it replaced.

Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/

Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics

20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

Which manufacturer made the keyless deadbolt lock? Make sure that the batteries are good in the unit.

I have an older Weiser Powerbolt deadbolt lock that is programmed by taking off the cover on the inside of the door. This model has handheld remotes and the keypad. Inside there are three yellow buttons. Two match the cover's lock and unlock buttons. Press and hold the third button (in the center of the set of buttons). Then enter program in the code within a few seconds and press the enter button to set the code. If the unit beeps again, the code is set. If the unit doesn't beep, retry from the press and hold the Program button step.

Another model of the Weiser Powerbolt lock has the Program button either on the top left or lower right hand side of the board (depending on the way the door opens) under the cover. Press the Program button once and then enter the 4-8 digit code. Press the Lock button to set the code. If you hear a long beep, the code was accepted; otherwise try to program your code again.

Kwikset Powerbolt locks are programmed the same way as the second Weiser Powerbolt described above.

Kwikset SmartCode locks have their Program button in the center of the bottom of the control board. Otherwise the programming is the same as that given above for the second version of Weiser Powerbolt locks.

MiLocks have three buttons in a horizontal line. The left-most button is the Set button. Press this then enter the code followed by the Unlock button. The code must be entered within 5 seconds of pressing set.

Baldwin Hardware's Boulder series of keyless entry deadbolts are programmed just like the Kwikset SmartCode units.

I don't know of any videos. Most manufacturers do have PDF files with the programming instructions.

I hope this helps. Please add more information about your deadbolt for extra assistance.

Cindy Wells
(I end up replacing the batteries often on the lock I have; it seems like they last 6 months or less.)

The main control board in you lock has gone bad and needs replaced.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

door pad keyless codes?

in owner manual, enter permanent code and then press "1" and enter personal code, then press "1" again. Then both codes will work.

If you don't have manual, go to Motorcraft.com and click on technical resources and click on your year owner manual.

---------------------------------------------
Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the Owner Literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit must be entered within five seconds of the previous button press.
Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:

1. Enter the factory set five-digit code (the keypad will illuminate when pressed).

1. Press 1/2 within five seconds of Step 1.

1. Enter the unique five-digit code.

The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it will simply overwrite the previous personal code. To erase a personal code, carry out the following procedure:

1. Enter factory set five-digit code.

1. Press 1/2 within five seconds of Step 1.

1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.

The system will now only respond to the factory set code.
Anti-Scan Feature
To provide added security, the keyless entry pad is disabled for one minute after 35 button presses without a valid entry code being entered. The keypad will flash during this one-minute mode with all functionality disabled except for 7/8 and 9/0 still being allowed to lock the vehicle.
Anti-Scan will be turned off after any of the following events:

• one minute of keypad inactivity
• the keyless entry remote transmitter UNLOCK button is pressed
• the ignition is turned to the ON position.

Unlocking the Doors with the Keyless Entry Keypad System
To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will illuminate.
To unlock all doors, enter either the factory set code or the personal code (driver door unlocks) and press the 3/4 control within five seconds.
Locking the Doors with the Keyless Entry Keypad System
It is not necessary to enter the factory set or personal code prior to locking all doors. To lock all doors, press the 7/8 and 9/0 controls at the same time.
Inspection and Verification

1. Verify the customer concern by operating the system.

1. Visually inspect for obvious signs of mechanical or electrical damage.

SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code

1. Enter the permanent factory keyless entry keypad code.

1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.

1. Enter the new five-digit keyless entry keypad code.

1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.

1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.

1. After all new keyless entry codes are programmed:
   • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
   • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
   • -------------------------------------------------------------

Programming —Transmitter

1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.

1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
   Press any button on the transmitter to be programmed.

1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.

1. To exit program mode, turn the ignition to START or wait 7.5 seconds.

--------------------------------------------------
Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.

1. Press the SET button on the driver door panel.

1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.

1. Press the 1 or 2 memory button on the driver door panel.

-------------------------------------------------------------
Programming —Autolock and Horn Chirp

1. NOTE: This procedure must be completed within 30 seconds.
   Turn the ignition switch to RUN.

1. Press the UNLOCK button three times.

1. Turn the ignition switch to OFF.

1. Press the UNLOCK button three times.

1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.

1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.

1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.

----------------------------------------------------------------------------------

does the key pad light when you press a button at night? If yes, the fuse is ok.
Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
report back.

Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
--------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical

• Keyless entry keypad
• Keyless entry remote transmitter

• Central junction box (CJB) Fuse F222 (20A)
• Circuitry
• Generic electronic module (GEM)

------------------------------------------------------------------------

• No communication with generic electronic module (GEM)

• Generic electronic module.
• Circuitry.

• REFER to Section 419-10 .

------------------------------------------------------------------------------------

1991-94 Nissan Maxima key less entry reprogramming procedure:

1. Enter the *original code found under the dashboard.
(*the code begins with the letter F and has 7 digits)

2. Close the doors and lock all of the doors,
enter the 7 digit code ( make sure you have your key in hand).

3. Once the code is entered correctly you will hear a long beep ♪ ♫.
While the beep ♪ ♫ is sounding ... ENTER your NEW 4 digit code, (you will then hear random beeps ♪ ♫)
Do not touch anything until the beeping ♪ ♫ stops.

4. To open the doors, the front windows and the trunk,
type: S(Clear) and the New 4 digit code and the door will open automatically.

5. IF by any chance you forget your new code. Just enter the original one and start all over.

I believe dealer has to re-program the new code.