Question about Sta Rite Sta - Rite 2hp Max - E Pro Inground Pool Pump, P6ea6g207l

1 Answer

How do you remove the pump? - Sta Rite Sta - Rite 2hp Max - E Pro Inground Pool Pump, P6ea6g207l

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

A pump is simple to remove. If the installer was smart, the put the pump in using unions. Unions unscrew and release the pump from the plumbing. This allows easy installation and routine maintenance. If you do not have unions, the solution is simple as well, cut the pump out, then re-install the pump using unions. A lot of home owners confuse the "pump" with the motor or wet-end of the pump. The pump is the entire unit, motor and all. The wet end is considered everything but the motor on the back. Make sure you follow the wire diagram, as to hook the appropriate wires back where they belong. I would suggest an electrician if you are not familiar with this.

Posted on Oct 10, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Remove motor

remove pump and replace with new

May 19, 2014 | Waterway InGround Pool Pump 1 HP

1 Answer

Makes noise does not pump

If the pump spins but does not pump water, most likely you have an air lock.
Try priming the pump with water or remove the air lock at the pump by removing the cover off the filter basket that is next to the pump.

Feb 25, 2012 | Emerson Threaded 1.5hp Fullrate 115/230v

1 Answer

My hayward northstar pump is humming but no water moves.How do I change the motor(pump)

Remove the 4 bolts that hold the motor to the pump ... remove the bonding wire ... of course, unplug the motor. The motor will easily come off the pump. Note the innards to assure you know what is the top of the difuser.

I think you will discover the impeller is fractured. Remove the back cover of the motor. You may have to loosen and move the capacitor. Find two flats on the armature ... 7/16 I think ... put a wrench on the flats to remove the impeller.

Replace the seals into the pump when you reassemble. Try to not touch the ceramic surfaces of present.

Thanks for using

Aug 18, 2010 | Hayward 2HP Pool Pump Motor A O Smith...

2 Answers

Where is the button to turn the discharge from vertical to horizontal? The manual states to "simply push the positioning button and rotate" - can't seem to locate the button!

Press the positioning button located on pump housing and rotate discharge port to desired position.

Note: the Discharge port will only rotate 1/4 turn.

Jun 02, 2010 | Hayward 1hp Power Flo Matrix Above Ground...

1 Answer

Removing pool pump impellor from motor shaft

Separate pump and motor. Remove diffuser. Remove back cover from motor. Motor shaft has either a slot for a screwdriver or a flat area for a wrench. Hold shaft and unscrew impeller.

Feb 24, 2010 | AO Smith A O Smith Motors Century 1hp 115v...

1 Answer

Removed four bolts,can not get motor off

depending on the pump you have, you'll need to remove the seal plate from the wet end and remove the impeller before you can remove the motor.

Nov 14, 2009 | AO Smith Pool Pump Motor 1HP Square Flange...

1 Answer

Proline Pump 8D-10-1n11CB. This is for a pool and is leaking from the shaft to the motor

The pump seal is bad on the unit. This requires disassemble of the pump unit. Remove power to the unit, dissasemble pump housing, remove the impeller from the shaft of the motor by removing the allen screw with an allen wrench. Seperate pump housing from motor remove the old seal replace seal. Lube motor shaft with a little clean oil or wd40 to facilitate easy install thru new seal,reassemble in reverse.

Jun 03, 2009 | Hayward 1.5 Hp Northstar High Performance...

1 Answer

Tring to take the pump face off the motor

You have to remove the back cover from the motor. Next loosen the capacitor. Put a 7/16" wrench on the shaft and the pump impeller will screw off by hand.

May 28, 2009 | Sta Rite 1 Hp Sta - Rite Abg Swimming Pool...

2 Answers

Removing a staRite pump

a picture on how 2 remove sta rite , remember to prime the pump after any repair !.. the shaft seal used on this pump is a 100 or a 200 . i use pac seal mechanical shaft seals cost about 10$.. go kits are not required on 90 % of repairs $$

Apr 13, 2009 | Sta Rite GO-KIT-6 Sta-Rite P2RA DuraGlas /...

Not finding what you are looking for?
Sta Rite Sta - Rite 2hp Max - E Pro Inground Pool Pump, P6ea6g207l Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sta Rite Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1224 Answers

john h

Level 3 Expert

7409 Answers

steve morris
steve morris

Level 3 Expert

1675 Answers

Are you a Sta Rite Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides