Question about Intel D845GVSR Motherboard

1 Answer

CPU incompatibil Have eMachines that had a bad power supply and took out MB. Purchased an identical MB with the same rev main number on the Intel sticker and now system will not boot up but it indicates the supported CPU speed is only up to 2.8Ghz before is shuts down in 10 seconds. The original is an Intel Celeron D CPU is 2.93Ghz.Do I have to install a 2.8GHz CPU? Or is there some other way around this problem? It is an identical MB, but it looks like the bios and bios chip is different.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 778 Answers

Do you get to the boot screen if so press the key to enter BIOS and set BIOS to default then from there set up to suit CPU and memory
Also check the M/board battery is OK

Posted on Sep 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

No power on


Start barebones and work your way up.
Unhook everything except the Power Supply, MB, CPU/with fan, Monitor, Power SW, and Keyboard (eg...no mouse, no hardrive, no cd-dvd....). If no post or no power it might be a bad power supply, MB, CPU, etc.....process of elimination.

Possible "DOA"

May 17, 2011 | Intel DQ45CB Motherboard

3 Answers

EMachines T2824. Does nothing but light on mainboard coming on...


This is a motherboard problem. You'll need to replace it. Although, it may be cheaper just to buy a new PC (eMachines are never very expensive, or well-made for that matter)

Sep 22, 2009 | Computers & Internet

1 Answer

Main MB powers on for about 15 sec then shuts down, power supply and front panel control both good, how can i get replacement MB


Check the CPU heat sinks and fans. Replace heat transfer material. If it powers up and doesn't stay on very long, it could possibly be detecting overheat or cpu fan stopped and shutting down.

Aug 12, 2009 | Intel Server Platform ISP1100

2 Answers

I have a emachine PC. PowerSupply blew up. changed it still down


Dear,

ELECTRIC SHOK OR IMPROPER EARTHING IS DAMAGE POWER SUPPLY,MOTHERBOARD,PROCESSOR,RAM
HOW TO CHECK IT.

(WHEN CHECKING KEEP CAUTION :- REMOVE HARD DISK DRIVE POWER SUPPLY SOCKET)

1. check power supply watt 400/450 and same another power supply install and check it. if power supply change and system is working ok so problem in your power supply.

2. check CMOS cell on motherboard,(3 volt)

3. Bfore power supply changing check on mother board any capasitor is like as damaged or not.
OR check main chipset ic is marked as intel.whenpower on it is very hitting or
normal)if very hitting require to repair your motherboard.(intel chipset ic near cmos cell or pci slot,)
4. checking of ram on other pc (working or not)(one beeps coming or not,if one beep coming ram is working ok)

Feb 27, 2009 | Intel D845EPI (INTELKD845EPILPAK10)...

1 Answer

Emachine T2890 won't power up. After reading some posts on this issue I went ahead and replaced the power supply, but the unit still won't power up. I am fairly certain that the old ps was fried since...


If you remove all the RAM fro the system and power it on, you should hear "Memory Error Beeps" if not, then it is usually Motherboard or CPU, for around $30.00 you can purchase a PCI POST code reader to try to pin the problem down further.
I am assuming from the post that all PCI cards (dial up modem especially) have been removed. Sounds like a bad MB or CPU, but if the video is integrated,( built on the motherboard, and not a seperate card, the memory is responsible for video also, and it maybe defective.

Feb 19, 2009 | Intel D845GVSR Motherboard

1 Answer

DG31PR Won't Boot


you ight have a BAD CPU, try checking it out on another pc or friends pc.

Jan 08, 2009 | Intel DG31PR Motherboard

2 Answers

Emachine W2047 No BIOS Start Screen


You can test the power button. Remove the wires from the power on pins on the motherboard. Momentarily jump the two pins with a small screwdriver. If the computer starts the power button is bad. If it still doesn't start then something else is wrong. Did you test the memory? Also do all of the fans work, especially the CPU fan? It can't hurt to test with the other PSU. You know the HDD is good. Test one piece of hardware at a time and hopefully you will find the problem.

Jan 07, 2009 | E-Machines eMachines Desktop PC

2 Answers

Emachine T3828 power switch connection to motherboard


The "Ultra Helpful Instructions" that Emachines provide (here: http://downloads.emachines.com/userguides/8511279_eM_NG3_chassis_HW_ref_en.pdf) state that when replacing the system board, "18. Attach all cables to new system board", but fails to say where that would be for each cable.

The site below says it's a genuine Intel board in there, so, congrats on that. http://www.e4allupgraders.info/dir1/motherboards/socket478/D845GVSR.shtml

And with that, the link to the manual:
ftp://download.intel.com/support/motherboards/desktop/D845GVSR/SR_English.pdf

You're looking for the info on page 32, I believe.

See if that fixes it up. If not, post back.

Jan 03, 2009 | Intel CELERON 2.66Ghz CPU AND MOTHER BOARD...

1 Answer

UpGrade


download cpuz it will tell your specs

Oct 18, 2008 | E-Machines eMachines Desktop PC

1 Answer

Motherboard won't boot


u can go to ur mb bios nd check ur processor setting.may be 845gvsr not support intel crl processor.u can give load bios default from ur bios press F6 or F7,

Sep 19, 2008 | Intel D845GVSR Motherboard

Not finding what you are looking for?
Intel D845GVSR Motherboard Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Tony

Level 3 Expert

2599 Answers

David
David

Level 3 Expert

778 Answers

Are you an Intel Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...