Question about Kenmore 23822 Top Load Washer

2 Answers

Does not drain all of water out unless you raise the lid during spin cycle

I have bypassed lid safety switch and did not help model # 238321

Posted by on

  • TeJay2 Sep 27, 2008

    I have the same issue with a Kenmore Mdl# 110.82671110. I have replaced the lid switch. I thought it was working. Still same result. Will Fill, will wash, will not drain or spin

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanx for trying, I gave up on it and purchased new units. Wife couldnt take it anymore. These were 22 years old. I guess I shouldnt complain. Everytime i would get it to start working, it wuld stop working again !!!!

Posted on Oct 21, 2008

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 62 Answers

This is sometimes the coupler, sometimes timer has shorted out.

Posted on Oct 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My maytag pav2300aww will not spin at all yet it agitates and drains well I was told to clean the agitator so I took it off yet the washer still don't spin the switch look wore out to me so I by-passe


Check the water level sensor and the lid safety interlock. Many washers will work fine with the lid open EXCEPT during the spin cycle, so this is the first logical place to look. Try bypassing the lid safety interlock switch.

Dec 12, 2012 | Washing Machines

1 Answer

My machine is filling up with water, but not washing or draining or spinning. Whatever cycle i put it on its doing the same thing. Can u help?


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Dec 19, 2010 | Washing Machines

1 Answer

My kenmore ultra fabric care heavy duty 80 series model 110 will not drain. The problem occured after a heavy load knocked the lid switch off during the spin cycle. How do i fix this/replace the lid...


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Nov 05, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

I have a kenmore 70 series top loader washer, model # 110 20712 991. It stops during the rinse cycle and does not spin or drain???


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Sep 15, 2010 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore washer 90 series will go through the cycle, rinse, but will not enter spin cycle, or drain the water from the basin. What could be wrong?


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Aug 24, 2010 | Kenmore Washing Machines

2 Answers

My washer won't spin or drain, but it will wash


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.



Jul 11, 2010 | Kenmore 22422 Top Load Washer

1 Answer

The machine quits on the drain cycle


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Jun 16, 2010 | Kenmore 22422 Top Load Washer

1 Answer

Water draining problem


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?modelNumber=110.20702991&pathTaken=partSearch

and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Jun 13, 2010 | Kenmore 27632 Top Load Washer

1 Answer

Kenmore washer - water won't drain. It stops


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.


May 12, 2010 | Washing Machines

1 Answer

Have to trip washer lid safety switch with something more substantial than little 'plunger' attached to the washer lid to get washer to drain and spin during rinse cycle. do i need to replace the safety...


removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet to replace it.

It comes as a complete unit and you can't replace just the plunger.

May 03, 2010 | Kenmore 23812 Top Load Washer

Not finding what you are looking for?
Kenmore 23822 Top Load Washer Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Ron Lankford

Level 3 Expert

5386 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

2mikecurtis

Level 2 Expert

65 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...