Question about Siemens SpeedStream Modem (4100) (SS4100)

1 Answer

Interconnect two remote sites

My request is about connect a remote site in our network without using fiber optics.

NB:

- The distance between the two sites is 500m.

- The number of post on the remote site east of 04 posts (Internet access, intranet etc ....).

- See used the opportunity to connect via modem-router

Best regards

Rafif

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,605 Answers

500m ethernet cable is at its max.
you can use 4 pair (8lines)telephone wire to semulate ethernet cable (unshield). you will pickup noise on the line.
only one unit can be the moderm to access the Internet the other has to be a router. (Lan port only). and you cansetup both to have wireless access.

Posted on Oct 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can 10GE Optical Interfaces of a Switch Work upon a Unidirectional Fiber Connection?


10GE optical interfaces of a switch cannot work upon a unidirectional fiber connection. A unidirectional fiber connection occurs between two 10GE optical interfaces when one interface is Down because the Rx fiber is removed, while the other interface is still Up because its Rx fiber can receive link_Up signals from the PHY layer.
A switch determines the status of a 10GE optical interface according to the IEEE 802.3ae standard. As defined in this standard, the MAC layer of a 10GE optical can send local_fault and remote_fault signals. A switch can determine the link status based on only the link status of the PHY layer or based on the link status of the PHY layer and the local_fault and remote_fault signals from the MAC layer.
On a Huawei switch, link status of a 10GE optical interface turns Up only when the link status of the PHY layer is Up and both the local_fault and remote_fault signals are 0. When two 10GE optical interfaces are interconnected and the Rx fiber on one interface is removed, this interface goes Down and the MAC layer of the interface generates a local_fault signal. Meanwhile, the local interface sends a fault signal to the remote interface through the Tx fiber. The remote interface receives the link_Up signal from the PHY layer and the remote_fault signal from the MAC layer. Therefore, the link status of the remote interface goes Down.
S2300 Switch Thunder link com

Jan 22, 2017 | Huawei Computers & Internet

1 Answer

No signal is received in the optical input of a 2000 ONKYO TXD 575 Receiver. Remote controller replacement for this unit too the model of the remote is RC-392M


Hi Ben please check the assignment of that port. The port could be bad. I checked several sites for a replacement remote and they are not available. Thank you Onkyo USA

Dec 29, 2016 | Onkyo Audio Players & Recorders

1 Answer

How to design the PAN port of Huawei OLT equipment?


1. General in order to avoid the two upward mouth is connected to a single point of failure, this state data from walking on the piece of the board, if the down off, from another piece of the board, because so that we can minimize the damage of equipment (such as the single board failure) caused by accident, because the pon is generally used for operators, the Huawei OLT if off, affect the users and business all too clear.2. In series between the OLT?Refers to the OLT between redundant or a simple link to each other?OLT can be seen as a layer 3 switching device, but its core technology is the control of the ONU below, interconnection between two OLT operation routing protocol can achieve what you said series topology effect.ONU series of words can be used in a beam splitter, as shown in figure.After OLT downward a 1:2 splitter, spectral ratio of 5 goes, than small optical fiber spectroscopic ONU, spectral than big same optical splitter, optical fiber again by one such a layer, in this way of deployment support 6-7 ONU () under the same pon mouth, perhaps because more droop too big to run normally.

Nov 02, 2015 | Huawei Computers & Internet

1 Answer

What is a network extender?


Wikipedia says: An Ethernet extender (also network extender or LAN extender) is any device used to extend an Ethernet or network segment beyond its inherent distance limitation which is approximately 100 metres (330 ft) for most common forms of twisted pair Ethernet. These devices employ a variety of transmission technologies and physical media (wireless, copper wire, fiber-optic cable, coaxial cable).

Feb 14, 2013 | Computers & Internet

1 Answer

Looking for a diagram on how to hook up my dish network box to my STR-de597


There is a wiring diagram PDF posted on Sony's support site. However it lacks a configuration for a satellite receiver. Without knowing your particular Dish setup, I'd say use the Component video cables and a fiber optic for the audio if you can. Otherwise, the component video and coaxial cables are your next best choice to get decent video and surround capability.
In both cases, you need 2 sets of video cables One for the in and another for the out. You only need 1 fiber optic or coaxial for audio if you do not plan on running the TV speaker system. Use the video 2 inputs for either video type.

Oct 27, 2009 | Sony STR-DE597 Receiver

1 Answer

Hp 4108 vs 2524


It has to be either the cable or the transcievers. Do you have a spare pair you can try instead?

Don't forget that HP has free tech support at 866-myprocurve also. They are excellent.

Jun 19, 2009 | HP ProCurve 2524 24x10/100 Mbps Networking...

3 Answers

Fiber-optic networking


Apply load balancing of the NIC interface, else put in a switch to interconnect all the computers. That should give equal speeds to all the PC's.....sodeep

Apr 06, 2009 | Computers & Internet

1 Answer

Canary CFT-2062 connection diagram


I tried to answer this for you yesterday but FixYa didn't put it through I guess. I'll try again.

That device is a "Industrial Media Converter". It is for converting a 100BASE-TX LAN cable into a 100BASE-F fiber optic cable for long-range networking. (2km) There are two ways to use it.

One:
Get two and convert LAN to fiber, then back to LAN.

Two:
Use it to tap into an existing fiber network, like fiber optic Internet.

For the first case; you will need some "Duplex" "multi-mode" fiber optic cable ($1.10 a meter) and an other one of those devices ($50~$300).

For the second case you will also need some fiber optic cable and you will need a network to tap in to. Of course you will need to clear everything with the company that owns that network before you can do any thing. And that’s assuming that they even use the same system level protocols.

To directly answer your question:

1: Hook the 100BASE-TX LAN port up to a PC, Hub, or a switch.

2: Hook up TWO multi-mode fiber optic cables to the device using CT style connecters. Hook one to the TX and one to the RX connectors on the unit.

3: Run the cable how you see fit.

4: Hook the other end up to the interfacing device. Be it joining it to an other cable in an existing network, or to another of those devices.

Note: The TX cable of one device goes to the RX of the other and visa-versa.

-Charlie

P.S. I also have one exactly like that one that I’m trying to find a use for.

Nov 19, 2008 | Canary (CFT-2062) Transceiver

1 Answer

Adding offices to my remote server


The SonicWall TZ 190 is a good appliance for the Tampa location.

The SonicWall TZ 150 is a good appliance for the remaining locations.

For the remote locations, a decision has to be made as to how many sites you want to interconnect to. If you want the network to be such that each site connects to every other site, then you will need the SonicWall TZ 190 as it supports VPNs for up to 15 sites.

In the end, everything comes down to cost. For a Small-to-Midsize Business, this is considered operational cost.


Hope this helps :) Kindly leave a rating. Thanks..

Nov 27, 2007 | SMC TigerSwitch 6508TT

Not finding what you are looking for?
Siemens SpeedStream Modem (4100) (SS4100) Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18375 Answers

john smith

Level 2 Expert

381 Answers

Are you a Siemens Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...