Question about Fisher and Paykel IWL12 Top Load Washer

1 Answer

My fisher & paykel washer will not move to rinse cycle

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Fisher & Paykel GW712 AU 93200-A STOPS @ THE RINSE CYCLE & THE SPIN CYCLE?

Posted on Oct 19, 2011

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
TheMobilian
  • 8220 Answers

SOURCE: Fisher & Paykel Ecosmart will Wash but not Rinse/Spin

You have too many clothes in the washer. Take some out and try again

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Posted on Sep 09, 2009

aborcass
  • 2651 Answers

SOURCE: Fisher and Paykel Smart Dribe 608

not familliar with that exact model number ( we dont have that over here in the US) we have simalair f&p gwl10- gwl11) that problem sounds as if either the pump is bad and overheating before pumping all the water or a diverter valve is not fully closing allowing water to remain in tub.














Posted on Mar 29, 2008

  • 17 Answers

SOURCE: fisher paykel smartdrive 601

Most likely a blocked pump

Posted on Apr 19, 2009

SOURCE: fisher paykel washer won't go into rinse cycle.

http://www.docstoc.com/docs/25379677/Fisher-and-Paykel-Circuit-Diagram-GWL11
www.fisherpaykelparts.net/partmanuals/GWL11US.pdf - United States Above is a circuit, and a service manual, below are two DIY Washer help sites, to help troubleshoot and repair, the service manual has all troubleshooting and repair instructions.
http://www.washerhelp.co.uk/diy-repair-help.html
http://www.repairclinic.com/Washing-Machine-Repair-Help

Posted on Jun 01, 2010

  • 30 Answers

SOURCE: Fisher Paykel Intuitive Eco Washer - IWL15: what is error code 136 on a fisher & paykel IW...

fault code 136 is a hard one possible causes are faulty rotor speed sensor on motor,siezed bearings or rotor,motor windings ,or motor control module, would suggest you get a tech for this one to diagonse correctty ,without proper tools to test eg: rss tester you could cot yourself more money... hope this was some help....:)

Posted on Jun 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher Paykel washing machine Smartdrive 703 Advance, Power and Start buttons are non responsive when pushed. Is there a part that can fix this. Does the control panel have to be replaced?


Fisher & Paykel Smart Drive beeps and stops during rinse cycle. If I hit pause and wait and restart it eventually continues. It seems like it has problems detecting water level.

Apr 13, 2011 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher Paykel washer spin issue


lift the front of the machine and set on blocks about 3"

reach under to back to the blak flexable pipe and squeeze several times to loosen hair soap gunk eccetera.

start mahine on rinse cyle

it should start to drain on its own

Jul 18, 2010 | Fisher Paykel EcoSmart GWL15

1 Answer

Hello my Fisher Paykel washer will go through the


clean the pump at the bottom of the washer (its the piece with the fan attached); also check the hoses at the pump

Jun 27, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

During the rinse cycle, our GWL 11 Fisher & Paykel


The problem is in the pump, so it will not pump out, you will need to find another way to empty it, removing the agitator will make the job easier.
When you get the water out the pump can be accessed from underneath, it turns anticlockwise to remove it,.
I would buy a new pump as it is most likely that is all that is wrong with it.

Apr 18, 2010 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

F&P washer lights on and beeps


Clogged pump stopped up drain. If the washer does not think all water was pumped out in 8 minutes then it shuts down. Slow drain is my first inclination.


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Dec 31, 2009 | Fisher Paykel EcoSmart GWL15

1 Answer

Fisher & paykel GWL11 washer won't rinse


sounds like you have two problems, the burning smell is probably the pump,out of balance is usually due to worn aout suspension rods

Oct 14, 2017 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher & Paykel Ecosmart will Wash but not Rinse/Spin


You have too many clothes in the washer. Take some out and try again

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Sep 09, 2009 | Fisher Paykel EcoSmart GWL15

2 Answers

Fisher Paykel washing machine model # GWL15 drips


Hi Dale..
It sounds like you have a leaky inlet valve assembly. The part number is 421029P and is easy to replace. You can get one here:
http://www.fisherpaykelparts.net/ecart/item.php?item_id=266&category_id=56

Apr 20, 2009 | Fisher and Paykel GWL11 Top Load Washer

3 Answers

Fisher paykel smartdrive 601


I can talk you through diagnostics if you want to go on live chat cheers

Mar 13, 2009 | Fisher and Paykel Fisher & Paykel Washer

Not finding what you are looking for?
Fisher and Paykel IWL12 Top Load Washer Logo

Related Topics:

928 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...