Question about Samsung LN-T4061F 40 in. LCD HDTV

2 Answers

No signal or weak signal

By cstewart5000, posted on Sep 21, 2008 My grandson pushed a botton on our remote. My husband tried to fix it. I can not get a picture at all now. I get the error message no signal or weak signal. Is there a way to reset the tv and let it reload? I've unplugged it and disconnected the cable over night thinking it would let me set it up again.

Posted by on

  • 1 more comment 
  • cstewart5000 Sep 22, 2008

    I was able to find help by downloading a owners manuel. I fixed the problem!

  • lowted Feb 20, 2009

    Have a Samsung LN 32A450CID

    Connected a DVD player and the following error message appeared: "Weak signal no signal"

  • Larry May 11, 2010

    Need the model of the TV and the Make ... 1st

    2nd do you have a cable box and what is your provider?

    Happy to assist

    LB

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

  1. Since my problem (Samsung/Comcast) began with a channel selection button pushed on the TV remote when it should have been pushed on the cable remote, I figured the problem lay with the TV.  Although I was getting the "weak or no signal" msg., the actual signal strength displayed as strong. Disconnecting did no good. I surmised that the box was simply not recognizing the TV.
  2. I looked at the manual for my Samsung 750 model. 
  3. Page 20 discussed "Selecting the source". I accessed the TV menu and selected "Input", then chose the "HD..." item from the highlighted list. Voila! My husband will be so proud of me when he returns from hunting camp.

Posted on Nov 18, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 84 Answers

Sorry I see the model,
hold the Menu button on the TV (not on the remote) down for three seconds.
Note: Shop Mode is activated in the same manner: Pressing and holding the Menu button on your TV for three seconds. To avoid accidentally setting your TV to Shop Mode, avoid pressing and holding the Menu button on the TV for three seconds or more.

Posted on Sep 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a bose tv speaker system. I have not used it in awhile. I cannot seam to get it working. the red light is on the remote device that sets under the tv.


Check the remote control for its infrared emission. Check it with fresh batteries. Check it by pressing all the keys. You can detect the presence of infra-red emission from the remote control, using a cell-phone camera. If you wish to get more details about how to check a remote control, please visit this site. One among the posts has details about it. Surf the site with patience. In some cases, the remote control might need to clean.
http://remotesearch.blogspot.com/
Search the site by type in this key phrase "how to test a remote control "in the "search box at the top right of the display window of the Homepage" to get the related post quickly.
https://www.youtube.com/watch?v=jsSCNCW3IbQ [open and clean]
https://www.youtube.com/watch?v=Qp-l1uh-5gE [open and clean]

Dec 14, 2016 | Bose Televison & Video

1 Answer

No display and all push botton switch not function


Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician.

Aug 07, 2015 | Televison & Video

1 Answer

Soniq qv420ph no display


It sounds that the start signal does not comes from its main digital board to its main power regulator board. There is nothing a user can do with this fault. It will be best to contact any service technician. If you wish to get some details, http://electronicshelponline.blogspot.com/ Pull up older posts.

Dec 17, 2013 | Televison & Video

1 Answer

I was watching t.v. my grandson called then i looked at the t.v. and it said no signal. i have tried unplugging it and turning it back on. i have changed the batteries in the remote control. nothing...


This seems to be due to the TV being on the wrong input. Use your Vizio remote and cycle through the inputs until you reach the audio inputs. Try all of them with the receiver on and the amber,green and blue lights on the receiver. If you do not see a picture here the TV may have been connected by coax. To check this go to th TV input using your Vizio remote and key in 03 or 003. You should be able to see satellite now. It will also depend on how your system is a connected to your peripherals if you have any connected.

Hope this solves your issue. Thanks for using FixYa.com.

Sep 30, 2010 | DISH Network 322 DTV Receiver

1 Answer

My grandson was watching an old VHS tape and pushed something. Now, all I see when I turn the t.v. on is "counter00.00" and then the t.v. shuts off in about 3 seconds. I have lost the owners manual. HELP!


Left up the VCR tape gate,see,if the tape still in there?Yes,unplug,10 mins.replug the Tv and push the tape forward botton.Let the tape go forward about 5 sec. eject the tape take out.Grandson probally rewind the same seen to many times,causing power power shotdown mode.

Aug 09, 2010 | Symphonic SC3813 13 in. TV/VCR Combo

1 Answer

My husband played with the remotes so now our Samsung shows with a banner of "Weak or No Signal" what do I need to do to get Comcast back?


Your Samsung is in "broadcast" mode.
On the remote, press the "source" button once... twice...until you get to the Comcast input.

Oct 11, 2009 | Samsung TV Remote Control

1 Answer

GARAGE CONTROL SYSTEM


Try holding the hand held remote up next to the homelink (built in remote). Hold down the botton on the hand held remote and the botton you want to program in the car at the same time until the homelink light goes out. This could take 60 seconds or more. Now depending on which model garage door open and how old it is you may need to program the car to the opener. Usually this is done by pushing the botton on the back(Liftmaster,Sears, Chamberlin) or the botton on the front(Genie) and then go to the car and push the same botton on more time. I hope this helps.

Feb 05, 2009 | 2005 Honda Pilot

1 Answer

Troubleshooting vcr


Usually one connects a RF [cable tv, Dish tv, antenna ] cable to the INPUT of VCR & a RF cable output to tv (antenna )INPUT .The reason is that if you are watching TV reception (Cable, Dish, etc) and you want to watch VCR tape, just push the tape in and it should start playing picture.
From what I understand that you are trying to say:: [ YOUR NEW TV ! ] you MUST connect to the RCA jacks, CABLE S with RCA plugs that come out of the VCR to the new TV [ INPUT & OUTPUT] jacks .When you ["" use input botton on VCR remote"" ] you are using a DIFFERENT input signal. You are not letting the TV know that you are changing the signal from RF(antenna, Cable, Dish,etc)to the RCA signal ["" I use my input botton on my vcr remote""]

Aug 14, 2008 | Televison & Video

3 Answers

Weak or no signal message


  1. Since my problem (Samsung/Comcast) began with a channel selection button pushed on the TV remote when it should have been pushed on the cable remote, I figured the problem lay with the TV.  Although I was getting the "weak or no signal" msg., the actual signal strength bar graphic showed it to be strong. Disconnecting did no good. I surmised that the TV was simply not recognizing the box.
  2. I looked at the manual for my Samsung 750 model. 
  3. Page 20 discussed "Selecting the source". I accessed the TV menu and selected "Input", then chose the "HD..." item from the highlighted list. Voila! My tv works again. 

Jun 08, 2008 | Samsung LN-S4092D 40 in. LCD HDTV

Not finding what you are looking for?
Samsung LN-T4061F 40 in. LCD HDTV Logo

838 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72230 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...