Question about Batteries & Accessories

1 Answer

Black and Decker Battery Charger

I am looking for the list of error codes and their meanings for the Black and Decker battery charger model BC40EB. I can't find the manual.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Fault Codes Meaning of Fault Code F01 Internal Shorted Cell Battery - Cannot be charged. Have battery checked by certified auto service center.
Excessive Load on Battery While Charging - Check load. F02 Bad Battery Connection - Check battery connection.
Battery Voltage Tool Low to Accept Charge - Have battery checked by certified auto service repair. F03 Internal Open Cell - Have battery checked by certified auto service center.
Sulfated Condition - Battery needs to be reconditioned. See manual. F04 Overtime Condition - Battery will not accept a charge after 18 hours of continous charging. Battery may have internal
damage. Have battery checked by certified auto center.

Battery Charge Rate is Set Too Low - Set charger to higher charge rate. See manual. F05 Overheated Condition - Disconnect charger and allow to cool for 30 minutes. Check for ample ventilation. F06 Reverse Polarity F07 Alternator Output is Out of Typical Operation Range

Operation Codes I=I=I=I Battery Reconditioning - (The letters DES will display for the first three seconds) I-I-I-I Alternator Voltage Check OOO Charger Standby FUL Battery Fully Charged

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

19.2 volt lithium ion battery


I can answer questions about this charger, but you have not posted a question. Basically if you get a red light when plugged in, it may be functional. You won't know until you try charging a known good battery. You should be able to charge both NiCd and Lithium Ion batteries. If no red light appears when plugged in, a component has failed on the inside. These can only be repaired by a skilled technician with solid state component knowledge and soldering skills. The case is held together by four T20 anti-tamper screws under the four rubber feet. Do not apply power with the cover opened.
Common problems are shorted power rectifier diodes, shorted movistor and opened fuse. If the fuse is not blown check the filter caps by shorting across their leads with a screwdriver. If you can an arc, after the charger has been unplugged for a few minutes, it means the switching regulator has failed. Usually this is a TOP256EN. If it has burned and blew a piece off the regulator, the transformer has probably shorted. If the regulator looks OK, it may work after replacing it. There are many more possibilities, but these are some basics. BTW, this is exactly the same as a Ryobi P113 on the inside except for the battery terminals and the board layout. They have the same components.

Dec 08, 2013 | Craftsman C3 19.2 volt Lithium-Ion Battery...

2 Answers

Makita battery


Check that you have the correct battery in the charger as the charger will not charge any type of battery, only the battery type listed on the panel.

May 06, 2013 | Batteries & Accessories

1 Answer

Energizer CH2PC-UK battery charger' how long do i charge AA and AAA batteries


Charge time depends on the mAh capacity of the batteries (should be listed on the package, or the side of the battery) most AAAs are under 900mAh so 2 hrs should be sufficient, but AAs vary greatly in capacity so heres a link to check after you look up your mAh rating
http://energizer.com/SiteCollectionDocuments/pdf/rechargeable/CHDC.pdf

Jan 14, 2011 | Energizer Rechargable Battery with Charger

3 Answers

What does the flashing red light mean?!?


The flashing red probably means that the charger is working correctly and is indeed charging the batteries. The light should turn green when charging is complete after anything from 1 to 16 hours depending on how this charger works.

Do the following test: Fit the charger with your batteries and connect it to the mains. After 1 hour check if there is a detectable temperature rise in the batteries. You can do this without interrupting the charge cycle by touching the cells with the back of your fingers. If the temperature is still low, let it continue for another 15 hours or so, checking every now & then for any temperature increase. Should the temperature rise more than a few degrees, then stop the charging by removing the charger from the mains. Should the red lamp remain flashing after 16 hours, then I suspect you to have a defective charger.

Dec 27, 2010 | Duracell AAA NiMH Battery Charger with 4...

1 Answer

I Have a Vector VEC011 Jump Start System and the battery has gone bad. Where can I find a replacement battery (12V, 9A) with Bolt on bus Terminals


In March, 2006, Black & Decker purchased Vector Products, Inc. Since the acquisition, Black & Decker has assumed the manufacturing of all Vector products. For customer service and warranty information for Vector products, please contact Black & Decker Customer Service.

Or, you may find a replacement battery here: http://www.batterywholesale.com/battery-store/SLA-batteries/

Sep 25, 2010 | Vector Manufacturing Simple Start Battery...

1 Answer

Charger model FY 4101 green light stay lite all the time, and hoveround battery is still dead


When the green light stays on regardless of dead battery, this means the battery is defective. The battery must present a load to the charger, which causes the charger voltage to drop, turning the charger on. When the battery is defective, it will not load the charger, and the charger voltage stays at full charge value. This of course, causes the green light to be switched on.

Sep 16, 2010 | Batteries & Accessories

1 Answer

Good day I've had the unit plug in for 48 hrs and


In March, 2006, Black & Decker purchased Vector Products, Inc. Since the acquisition, Black & Decker has assumed the manufacturing of all Vector products. For customer service and warranty information for Vector products, please contact Black & Decker Customer Service.


Aug 08, 2010 | Vector Manufacturing Simple Start Battery...

2 Answers

The LED's on my Energizer charger flash red and green constantly.


If your charging 2 batteries only they must be palced in the following poistions on the charger
1. both side by side in the 2 left slots

or

2. one each in the two right slots.

Otherwise the batteries will not charge.

The users manual can be downloaded here:

http://www.energizer.com/SiteCollectionDocuments/pdf/rechargeable/CHDC.pdf


Thanks for using FixYa.

Kelly

If the batteries are charging the battery indicators

Mar 24, 2010 | Energizer Rechargable Battery with Charger

2 Answers

Ez Go 28115-G01 battery charger does not work.


I have an EZGO powerwise 36V charger, model 28115-GO3 that was installed onboard a cart. I want to use this charger for another cart, but the charger has 3 wires out. Why 3 wires? One is +, the other -. what do I do with the third wire? The wires are red, black and yellow; two odf the wires are 10-12 gauge, the other is around 16 gauge.

Mar 26, 2009 | Batteries & Accessories

Not finding what you are looking for?
Batteries & Accessories Logo

Related Topics:

5,405 people viewed this question

Ask a Question

Usually answered in minutes!

Top Batteries & Accessories Experts

Carl Glas
Carl Glas

Level 2 Expert

283 Answers

kakima

Level 3 Expert

96467 Answers

Jay Finke
Jay Finke

Level 3 Expert

1222 Answers

Are you a Battery and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...