Good Batteries, but I think I used the wrong ac power adapter supply. After looking the one that I used fit just fine, but the voltage output was 7 volts. This cam requires 3. Is it worth trying to fix?
An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
Re: Fuji pine pix a600 will not power up.
Possibly not worth repairing. You may have ruined the internal parts from over-voltage. Any thing has a value to the owner, thus it is up to the owner as to how much he is willing to pay on repairs to fix the item. This applies to cameras of any kind, cars, houses, and so on.
I would suggest to look up the value that your camera has been selling for (on a site such as Ebay). How old is it? If it is over a couple years, the value may not outweigh the cost to repair. That will depend on the condition and other factors.
If the internal parts have been burned out, then the cost to replace a main board ,probably what you need, may be far more than what you want to pay. Since this is a 6.3 mpxl. camera, I would guess it is over two years old, and will not bring more than $100.00 if sold in good condition with all the things it had when new. A suggestion is to sell this camera as parts on a site like Ebay, and get what you can. You may choose to sell all or just the camera.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
see this causes and proceed . God bless you If the camera won't turn on, check the batteries, or connect the
camera to an AC adapter. If that doesn't work, remove all batteries,
disconnect the AC adapter, wait a minute, reinsert batteries and
reconnect the adapter.
If the flash doesn't work, the camera won't take pictures, or the screen keeps turning off, check that the batteries are strong.
You may have improver card fitted. Please remove and re fit the card. If problem persist , please try another good / new card. If you have no problem with new card, your existing/previous card is broken.
The problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the
probability is that you will have to get it fixed by a professional.
these at own risk as it may further damage the camera.
try connecting your ac adapter or usb cable.
Try holding the
shutter button while switching on the camera.
Look at the lens ,
and if some of the lens 'circles' is misaligned or not concentric then
try wiggling it (while holding camera lens down).
pushing or pulling the lens when it extends but this is risky as it may
cause the lens barrel to slip out of its guidance system.
way to do this is to place the camera lens down on a hard surface and
then power it up. Be sure to use a soft cloth or something similar as to
not scratch your lens or casing. Let the lens push the camera up and
down a few times and sometimes the little resistance provided by the
camera is enough to get things going again.
Try hitting your
camera near the lens on the body with the soft tissue on the palm of
Other than that , I would take the camera to a repair
center for a evaluation to see if it would cost more to repair than to
replace the camera.
If it is still under warranty I would suggest
you take it in before trying any of these steps and remove any
off-brand batteries or accessories as some stores are really fussy about
warranty repairs on camera's with non-brand accessories.
If an SD memory card is installed, remove the card.
Remove power from the camera as described below:
If you are using only batteries for power, open the battery/memory card door and remove both batteries.
If you are using only the HP AC power adapter, disconnect it from the camera.
If you are using both batteries and the HP AC power adapter, remove both batteries and the power adapter.
Wait for 15 seconds. Then reinsert the batteries and close the battery/memory card door or reconnect the HP AC power adapter to the camera. If you are using both batteries and AC power, try each method separately.
Turn the camera on and off. If the issues is not resolved do the following
Connect the camera to the optional AC power supply
Connect the camera to the optional AC power supply. Ensure that the AC power supply is connected to a working power outlet.
Try turning the camera on.
If the issue is resolved , you do not need to continue with the rest of the instructions in this document.
If the is not resolved ,then repeat setps 1 to 4 abiove but remove the batteries and keep the AC power adapter connected.
You will need to do a firmware update to be able to use your new 'M' XD card. Also you will need a AC adapter to be able to use the update for your camera.
It is a Fuji site and it works.
Good luck. http://www.fujifilm.ca/x3719.xml
Ouch! You can't use an AC adapter with any battery-operated equipment you choose to just because the plug fits physically. The A70 requires 5-6 volts, and a Pavilion adapter typically puts out 18 volts. You most probably blew out your Canon's power supply within a few seconds, unless it's fused somehow. Next stop: tech support/repair shop/camera cemetery. Sorry.