Do you know which sensor # or name it is? If so, open the front of the case and type in your master code. Then select "delete" from the top row and then either type in the number of the sensor unit (ex: 08) or hit the remote/sensor button and cycle through the ones you've got until you hit the right one. Hit the "done" button and you're finished.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
From your description, it seems that the transmitter section of SC-001 is working properly. What you have done to reinstall the system may not be thorough. And it is unclear whether the control panel is not responding to keychain transmitter or sensor or both.
I assume that you have followed the instructions in the manual to clear the zones. Simply unplugging the AC power and removing battery will not clear the zones. Note that sensors can be programmed into zones 1 to 4. Keychain transmitter can be programmed into zone 5 only. There is no LED indication for zone 5.
Secondly, follow the instructions to program the sensor or keychain transmitter to the control panel. The corresponding zone LED will be flashing during programming. There is sound indication as well for successful programming of the device.
If you do not program the sensor or keychain transmitter to the control panel after clearing the zones, the control panel will no longer respond to the device.
The dialer and siren is not cleared on the control panel. They can be cleared only from the dialer or siren itself.
Hi , to test door magnet put close a small piece of iron, it should be attracted, this sensor is very rare to fail, possible the door sensor is faulty, this is a magnetic switch, to test it, you can put together both wires going to it (doing a short circuit to sensor), if the cable is OK the indicator of an open door should turn off and system will go to ready state. If all this happens, you need to change door sensor.
we provide some of the best reviews removing services and boosting sides and pages. this is internet reputation management company contact whatsapp only +91-9911233016 we will help you
Manual for this sensor is not available. In the Zenith I have installed The motion sensor battery slot was h at the back side of the sensor, you had to remove the sensor from the wall sliding it on one side to access the battery. It mounted two AA batteries, not AAA.
You either have a bad battery in the transmitter or a bad transmitter. If you replace the battery and it fixes the problem you are fine. If the battery doesn't fix the problem you will need to replace the transmitter.
You must have the installers code or the Ultility code to do this. If it was not changed by whom ever installed it, the code will be 4321. To find out open the face cover by pressing down on the center tab on top of the master unit and the face folds forward. It will enter code, try the 4321 if nothing happens/ no speach that is the wrong code and you must close face cover until you get the right code If it lets you into programming mode then you press delete then system will ask for sensor number, 01 to 24 ? So if bathroom window was sensor 7 you enter 07 then press done. It will sensor deleted. Then to add new sensor, press add, will prompt you the trip sensor, most units you remove the cover tripping the tamper switch , the system will beep and say sensor programmed, then proceed to group type enter 13 for instant alarm then press done button and close face. You are now done !
You need to use an installer code to add/remove sensors. Depending on what number of digits your alarm code is set for will determine the number for the intaller code. Look in the installer manual for the code. Then follow these steps:
Open the panel.
Key in installer coe
Activate the sensor you want to add. Some sensors have a button, some have to opened to activate.
Choose sensor name and group. Groups are listed in the manual. Basically, if you want the sensor to arm when the doors arm (such as for a window sensor or door sensor) put it in group 10 or 13. If it's a smoke sensor, group 26; motion detector, group 17 and keyfob, group 01.
Press done when finished and run the test to make sure the system is reading the sensor.