Question about Air Conditioners

3 Answers

Electric blanket controller light blinking - Air Conditioners

Posted by on

  • 2 more comments 
  • Anonymous Nov 18, 2008

    my controller light is blinking, why?

  • chrissykla Nov 20, 2008

    so is mine!

  • Anonymous Jan 31, 2009

    RESETING electric blanket by bedford how to do it

  • judith pezzuto
    judith pezzuto Jan 07, 2014

    cotrol box is displaying e instead of a number?

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 379 Answers

I had the same problem , i believe it was caused by unplugging the blanket plug while it was in the on position , i unplugged it from the wall and it like reset itself , worked for me.

Posted on Dec 20, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have a flashing FF on my control...it is supposed to self shut off after 10 hours,,,but this is what happened,,,now what? how di u reset...I've looked everywhere!

Posted on Jan 31, 2010

  • judith pezzuto
    judith pezzuto Jan 07, 2014

    contrl box is displaying e

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Why does my electric blanket controller light blink? Margarett

Posted on Dec 31, 2008

  • goatladies Dec 31, 2008

    I unplugged my electric blanket from the wall to reset itself because it was blinking but it still blinks.

×

1 Suggested Answer

  • 1 Answer

SOURCE: My Sunbeam electric blanket controls

Same problem, but now it is ok.  I emailed Sunbeam and was told that if my blanket was not plugged directly into a wall outlet it was not getting enough power and I needed to plug it into a wall outlet taking these steps:
1) Unplug from the surge protector/extension cord 2) Unplug from the blanket 3) Plug back into the blanket 4) Plug into a wall outlet

Posted on Dec 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E on controlls


If you have a digital control, it is designed to flash "E" on the display to notify you that a problem may have been discovered. Gradient controls and warming throw controls use a blinking indicator light for this purpose.

Follow the instructions on the flag tag to reset the control or follow the steps below.
  • Unplug the system from wall outlet.
  • Check that the control is well connected to the module.
  • Plug the power cord into the wall outlet.
  • Set the control to "on".
If the system still does not operate, disconnect the power cord and contact sunbeam
Sites sunbeam Site

Jan 11, 2015 | Sunbeam Twin Heated Blanket Navy Blue...

1 Answer

When I plugged in the cord to the blanket, it displays a continuous blinking of the letter F


Sunbeams - blinking "F" means that the connection to the blanket was loose. Make sure you give it a good push to get the piece fully engaged.

Nov 18, 2014 | Sunbeam Twin Electric Auto Heated Blanket-...

2 Answers

Can electrical cord for electrical blankets go between mattress and box spring


Wires should be on the floor. Do not put them where you may lay on them and or cause friction on them (even if it's just rolling over during the night).

Sep 19, 2014 | Sunbeam Twin Electric Auto Heated Blanket-...

2 Answers

Power cord for the Sunbeam electric twin blanket


Haven't you contacted the company that shipped it to you? It might have been an oversight and they'll mail you one. You can do that for anything you get shipped to you from a company.

Nov 28, 2013 | Sunbeam Twin Electric Auto Heated Blanket-...

1 Answer

I bought a Sunbeam electric blanket in december and only used it for about 3 months until it stopped working. i have done nothing that would cause this to occur and after searching online found that this...


The only thing you can do, other than pull all the wire out to test it, is check the temperature control. If you have another you know works or can borrow one to test the blanket, that's the easiest. Else, you will need to use a "Glow Stick". A Glow Stick is an electrical tester that does not require physical contact with a bear conductor to detect voltage. They are available at Hard Ware stores, Menard's, Home Depot, etc. Plug the blanket controller into the wall outlet and touch the 2 wires near the thermostat. If it glows, the cord is good and the outlet has power. Now test the wires coming out of the thermostat that go to the blanket. Turn the thermostat way up and down and see if the light glows. If no, the thermostat is bad. If it glows, indicating power has made it through the thermostat, continue to test along those wires to the blanket. If you have power at the plug on the blanket, continue onto the blanket along the wires that provide the heat. The light will continue to glow on-till you get to the break in the line. When the light goes out, that's the break point. If you do find a break in the blanket and would like me to walk through the repair, I will be happy to. The Glow Stick is a good investment for safely testing anything electrical without the risk of being shocked. Please rate this for me. I am new to the site and need to improve on writing what I am thinking. Let me know how it goes for you, OK?
Roger

Apr 02, 2011 | Air Conditioners

1 Answer

Where is the nearest repair, or new Sunbeam Electic Blanket Control service or sales store -- Fort Worth or Dallas, Texas. I am in North Richland Hills, TX


The customer service website for Sunbeam Electric Blankets is:
www.sunbeambedding.com

The Customer Service Phone Number is 1-800-892-7684.

Good Luck in your endeavor! :-)

Mar 01, 2010 | Sunbeam Air Conditioners

12 Answers

My Sunbeam electric blanket controls blink when I plug the control cable into the blanket. I cannot turn the controls on or off.


Same problem, but now it is ok.  I emailed Sunbeam and was told that if my blanket was not plugged directly into a wall outlet it was not getting enough power and I needed to plug it into a wall outlet taking these steps:
1) Unplug from the surge protector/extension cord 2) Unplug from the blanket 3) Plug back into the blanket 4) Plug into a wall outlet

Jul 21, 2008 | Air Conditioners

Not finding what you are looking for?
Air Conditioners Logo

Related Topics:

2,888 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air Conditioners Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Bill Long

Level 3 Expert

577 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you an Air Conditioner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...