Question about Uniden BC350C Base Scanner

1 Answer

Cannot set it. - Uniden BC350C Base Scanner

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Need to known how to put the number in my scanner . it was unpluged for a little while and it lost all of it numbers. i have the numbers just don't known how to put htem back in

Posted on Jan 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I turn this product on I only get static is there a basic setting that I can set the radio at and how>


you need to set the squelch to silence the receiver until a signal comes in google up the user manual for it and read it cover to cover.

Oct 11, 2014 | Grecom psr600 digital triple trunking...

1 Answer

Homepatrol scans but does not stop at any signels


Squelch setting set too high perhaps, reduce the squelch until you can hear something, then turn it up slowly until it start to scan again.
Radio Control Bar
The row of buttons across the top of the Main screen lets you fine-tune HomePatrol-1 reception, access Help, and reenter system configuration.
Button
Definition
Squelch
Sets how strong a signal must be before HomePatrol-1 stops on it.
Range
Controls how many channels are selected based on your location and systems' locations. Small range settings result in fewer systems and departments selected. A selection bar lets you set the range in 2-mile increments. Each screen tap is 0.5 miles.
Atten (Attenuation)
Reduces signal interference if you are in an area where there are a lot of radio signals. If Attenuation is set to ON, the status indicator turns red.
GPS
Displays the status of a connected GPS unit.
Help
Displays Help text.
Tap and hold to redo initial setup configuration.

Hope this helps
Ed

Oct 03, 2013 | Uniden Radio Scanners

1 Answer

Comunication error with 796d and computer.there's no serial port on my computer, so im using a rs-232 to usb. dosen't matter what usb port i use on computer, it still does not work. im using the...



  • Hi, I can help.

  • This happens a lot to people just setting up a scanner like this. Try these suggestions, I think you'll be up and running in no time.

  • You have to make sure the BAUD rate is set and make sure your PC control is turned on in your scanner. A BAUD is the rate per second data is sent.. A BAUD rate of 38400 (or what ever BAUD the software is at). I think parts 3,4 and 5 in the your scanner menu cover this. If you have the FIFO buffer set then remove it from your settings > control panel > comm ports. You will get the best results if you have that software read the bank before writing to it. Relabel your comm port settings if you need to as well ie. port 1, port 2 etc.

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa,

Regards, Tony

Sep 21, 2011 | Uniden BC796D Base Scanner

1 Answer

How can i hear what they are saying without that awful loud sound when they arent saying anything. cause when i turn the volume down i cant hear what they are saying


Turn up your SQUELCH button when no one is talking until the static noise just goes away.

Now your set will remain quiet until someone talks.

If you set the squelch too high it will also cut out the people talking, so always try to have it set just slightly above the background static level.

Good luck.

Apr 15, 2011 | Uniden BC350C Base Scanner

1 Answer

Batteries run down in a little over half a day in my new uniden BC72XLT scanner, is it batteries, charger or scanner?


its most likely the scanner. i had one that used up batteries pretty quick. my advice would be to get rechargeables, and get 2 sets of batteries so when one set runs down you can put the fresh set in the scanner

Jan 13, 2010 | Uniden BC72XLT Handheld Scanner

1 Answer

I have bought the uniden 369t scanner an i have static problems


check your squelch settings and make sure priority settings are in the off positions also be sure weather priority settings are off

Mar 07, 2009 | Uniden BCD396T Handheld Scanner

1 Answer

My phone is in the announce mode. callers cannot leave an answer,


What is the specific model of your phone. Typically there is a setting in your machine to set the "Recording Time". Uniden typically you can set to 1 minute, 4 minutes, or "Anounce only". This last one is probably what your is set to.

Typically pressing the "Menu" key will go to each setting for each time you press the button. Press menu until it announces "Recording Time" Then select 1 minute or 4 minute using the "Select" Button.

You can get most of the manuals for your uniden phones at :
http://www.uniden.com/products/index.cfm?cat=Cordless%20Phones%202.4%20GHz%20Digital

Select your paticular phone and see if they have the phone listed.

elijam1

Dec 16, 2008 | Uniden BC72XLT Handheld Scanner

1 Answer

Icom r5


A quick "get you started" guide.....

First set the squelch (gets rid of the hissing noise and allows the radio to scan)
to do this....

On the side are 2 buttons, the bottom one is monitor.
press and hold then look at the display,
turn the top dial until "AUTO" appears,

The squelch should now keep the radio quiet.

Now the tuning step..
You need to set this because if your radio was on 450.000 and you wanted to listen to 450.012.5 you would miss it if your radio was making 000.025 "steps". IE you would need 12.5 steps. This is the most common step used by ambulance etc in the UK, you will need to check local band plans.
Stick with 12.5 and you should get most stuff on VHF / UHF.
For airband 12.5 will get most stuff, but some is now changing to 8.33.
For HF (below) 136 Mhz I'd use 5

To set the step....

On the front there are 4 big buttons.
press [V/M.S.MW.SKIP] to select VFO mode,
then press [BAND.LOCK] to select the band you want to listen to,
then press [TS.SET] to enter the step
turn the dial to select your step (stick with 12.5 for now)
press [TS.SET] to exit back to VFO mode



To scan...

First set the scan type...
On the front there are 4 big buttons.
Press and hold the one that says [MODE.SCAN] for 2 seconds and look at the display,
turn the top dial until the screen reads ALL,
press [MODE.SCAN] again and the radio should start to scan with the 12.5 steps you set earlier.
If you want to change scan direction, just turn the top dial.
If you want to stop the scan, just press [MODE.SCAN].

When you hear something interesting, make a note of the frequency on the display.

To set memories (store frequencies).....

On the front there are 4 big buttons.
press [V/M.S.MW.SKIP] to select VFO mode,

to get close to the frequency you made a note of, press [BAND.LOCK]
Then set the actual frequency with the top dial,
press and hold [V/M.S.MW.SKIP] for 2 seconds to select memory write mode (1 short and 1 long beep)
turn the top dial to select which channel you would like to overwrite. Start with 01.
press [V/M.S.MW.SKIP] for 2 seconds. ( 3 beeps )

Thats it!

Any more problems just post on here and either me or someone else will help.

M3ODQ

Jun 24, 2008 | Icom IC-R5 Handheld Scanner

Not finding what you are looking for?
Uniden BC350C Base Scanner Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Radio Scanners Experts

Iron
Iron

Level 3 Expert

3018 Answers

Robert McClure

Level 2 Expert

160 Answers

John
John

Level 2 Expert

473 Answers

Are you an Uniden Radio Scanner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...