Question about Washing Machines

1 Answer

Washer is off balance for a kenmore elite quietpak he4t How do you level washer?

Posted by on

  • ffrog7655 Sep 20, 2008

    Thank you so much I appreciate your help

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,028 Answers

Adj all 4 feet all the way in..try to rock washer adj front feet as need to give washer as solid footing as possible tighten lock nut in top position against washer bottom ..adj only as much as need ..the further out the feet are the more likely the washer is to vibrate ..a weak floor is the biggest reason washers vibrate ..if washer is on a pedistal be sure the for screws holding pedistal to washer are tight adj pedistal legs same as washer feet so bottom of pedistal is as close to floor as possible

Posted on Sep 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a kenmore elite smartwash quietpak 9 HE4t. The control locked light is on. I have tried unplugging for an hour and plugging back in, door is unlocked but no buttons work. What can I DO


The following link explains how to correct a Control Lock problem on a Kenmore Elite:

http://www.fixya.com/support/r2469429-kenmore_elite_amp_whirlpool_duet

Some front panel features differ between models, but the instructions should be listed on the front panel of the washer, and are located in the operator/owner's manual. If these preliminary measures do not work, you may have a mnore serious problem.

If you have any questions, please let me know. I hope this helps you.

Aug 23, 2009 | Kenmore Elite HE5t Washer

1 Answer

Iget a f-11 trouble code on my kenmore elite he4t washer.


REplace your MCU. The MCU is the Drive Motor Control board and is located in the rear of the washer adjacent to the Drive Motor on the left-hand side (facing from the rear with the back panel removed). The wiring harness can also cause the error, but it is not as common a problem. Go onto kenmore.com and find your right washing machine and replace the part yourself. First try and take the wiring harness off and then reconnect it and see if the error code goes away if it doesnt then replace the part. Please Rate. Thank you

Feb 12, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

HE4t kenmore washer rubber drum gasket not attatched.


Removed the top and Front reinstalled the counter balance. the rubber gasket has a 1" tear in it which I patched with a rubber tire patch for now. Two of the locking nuts for the leveling of the machine were loose it went out of level causing the machine to rock and probably caused the counter balance to loosen up. My daughters come in from collage and over load it on weekends which adds to the machines demise. All have been warned.

Jan 17, 2009 | Kenmore Elite 45986 Front Load Washer

3 Answers

Kenmore Elite HE4t washer won't spin


The motor controller board is likely bad.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 06, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore Elite HE4t Washer Control lock lit, door locked


121 MINUTES USUALLY DRAIN CYCLE PLZ REMOVE 3 BOTTOM PANEL SCREWS 7 MM SCREWS, TO OPEN DOOR SLIDE RIGHT HAND TOWARDS DOOR LOCK ,THERE WILL BE A SMALL LEVER TOO PULL DOWN ,NOW ITS OPEN,,, SINCE U HAVE BOTTOM PANEL OFF PUMP IS RIGHT IN FRONT REMOVE PLASTIC HOUSING CLOCKWISE ,,,REMEMEBER HOLD 3 GALLONS OF WATER STILL ,HAVE BUCKET READY ,NOW CLEAN OUT PUMP AND DEBRIS ,, CLOSE IT UP SHOULD BE FINE NO MORE PROBLEMS ,,,,,

Jan 01, 2009 | Kenmore Elite 45986 Front Load Washer

2 Answers

Door stuck Locked Control Locked light on


Try unplugging the washer for at 30 minutes to reset the computer, first. If this proves unsuccessful, you can retrieve you clothes by using the manual release. The following link explains how:

http://www.fixya.com/support/r622155-kenmore_elite_whirlpool_duet_door_jammed

Once you retrieve your clothes, try running diagnostics on it. You can envoke the diagnostic sequence by selecting DRAIN/SPIN, NO/SPIN and then pressing any button under OPTIONS 4 times (must be the same button). The display should go to "C00" as the washer begins a sequence of tests that checks the fill functions, door lock, dispenser functions, motor speed, spin and drain. Allow the washer to run through the entire sequence and shut off. If anything is wrong an error code should be generated. Hopefully, all you had was a minor glitch. Let me know how things turn out. I hope this helps you.

Aug 25, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

HE4t King Size Washer Balance Problem


remove the lower acess panel ( 3 screws across bottom) check for broen suspension/shock absorbers

Mar 02, 2008 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

2 Answers

Kenmore Sedona Elite 3.8 Cubic Foot HE4t Washer (Front-Loading) 45089


open lower front with a starshaped bit(screwdriver) three small screws, to get to white plastic cleanout (easy to turn by hand)may have someting stuck in it. about a gallon of water is there so have two big towels ready to soak it up.

Dec 28, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...