Question about Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

F-01 my wahing mechine is not letting water go though it keeps flashing f-01 what does that mean

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I went on to the hotpoint website which told me what was wrong

Posted on Sep 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pump 14292 for power washer


Water should come out the tip even if the mechine is not running if the water is on. So there for now water is flowing through the punp at all witch mean you have a problem with a restriction of water flowing through the pump . What dose it do with the engine running dose the blow out valve open and water come out there . Dose the pump spin .Is there water in the pump oil .How often do you use the mechine and is it kepted in the cold over the winter with out winterizeing it Give more information mabey i can help you but it dosn't sound to good now

May 28, 2012 | Briggs & Stratton Garden

1 Answer

I have a LG direct drive wahing machine and its flashing IE cant find manual what does it mean please help!


An IE error code will appear if the washer has not filled with water in approximately 8 minutes. Check to make sure both hot and cold-water taps are open completely. After both valves have been opened, unplug the washer for 10 seconds and retry the wash cycle. There are filters on the inlet hose connections of the washing machine. If clogged, water will not flow through these filters into the washer. Disconnect the inlet hoses from the back of the washing machine, and clean the inlet filters gently but thoroughly. wm_inlet_filter_removal(1).jpg If this doesn't work then you will need to change the water inlet valve by removing the top panel.

Mar 15, 2011 | LG Washing Machines

1 Answer

Indesit wahing machine WIE 167 keeps filling with water and did flash H2O have replaced the switch mechinism inside but to no avail tube is not punctured or coroded - will not go onto wash cycle but will...


You need to clear out pressure chamber the part the at tube plugs into the chamber it will be clogged, stopping air going to pressure switch...This should cure..

Oct 07, 2009 | Washing Machines

3 Answers

Error Code "TEST"


Just had the same problem & found the following solution via the web :-
1. When tESt shows hold down both the ON/OFF Button & the START Button together & let the Test proceed holding the two buttons down for the entire test (Approx 3 Minutes ) .
Continue to hold the " buttons down until the word Done appears.
After which you should be able to proceed with the normal wash cycle

May 28, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Keep washing never stop.


either the heater is faulty or pcb corrupt.. have you any flashing lights as these are fault codes.

Feb 21, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Error code on electrolux


Haven't tried your solution but I'm keeping it in mind. I talked to a repairman and he suggested I remove the panel at the bottom of the dishwasher (left side). There I will see a red button which is the control board processor reset button.

This worked but if the problem reoccurs I will try your solution as it is easier than removing a panel.

Dec 28, 2008 | Dishwashers

1 Answer

Help with whirlpool awm 8103/1


Okay, ther manufacturer recommends unplugging the washer for at least 30 minutes to reset the computer. It could be you have a momentary glitch causing some problems. If you still have the same problem after leaving the washer unplugged, the following link explains the "FH" error code:

http://www.fixya.com/support/r615354-fh_error_code_whirlpool_duet_kenmore

If your clothes are stuck inside and you still cannot get them out because the door will not unlock, you will have to use the manual release to open the door. The next link explains how:

http://www.fixya.com/support/r622155-kenmore_elite_whirlpool_duet_door_jammed

I hope this helps you. If you require additional assistance, please let me know.

Aug 27, 2008 | Whirlpool GHW9300 Duet Washer

1 Answer

Kenmore Elite HE 5t


Low or no water supply, hot or cold side or water pressure switch not switching over to indicate fully filled though if this happens drain motor will continue to run continuously while f-20 flashes

Jan 15, 2008 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WMA42 Front Load Washer Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

puggy666

Level 1 Expert

47 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...