Question about Raymarine RL70CRC GPS Receiver

1 Answer

Plotter Rl70c no image

Hello i have a RL70c combined plotter radar unit at switch on the screen is white with no images atall can you help

Posted by on

  • noih Jan 13, 2009

    I have exactly the same problem, I would be interested in buying one as a replacement.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Sounds like it died...i happen to have one for sail with 4k dome

Posted on Oct 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do not get any images on the radar screen


depending on which radar it is, it may be the video coax inside the radar cable. Otherwise possibly your magnetron or mic. Try calling mid-shore electronics @ 410-228-7335 they may be able to assist you.

Nov 21, 2009 | Furuno Navnet 1834C/NT vx2 Radar C Map Nt

3 Answers

Ais and 1920c Furuno chart plotter


n the system setup, under “UNITS” I set BEARING to “MAG” (magnetic). This will cause the unit to display course / bearing information in relation to the Magnetic North and match magnetic compass readings. It is not the same as True North! One has to be careful with this setting. There are a number of areas where the earth's magnetic field is locally disturbed, sometimes very significantly. Your GPS may not account for it. - again, under “UNITS” I set “METRIC”.

Sep 02, 2008 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

Hello there, I have a 4' radar antena with a


ahh, this is an old one check the book.(ha, ha)
Press and hold menu during start up Choose "Installation Mode" Press "Menu" Select "Radar Set Up" Press "Next Page" Select "Radar Heading Alignment" Use knob and follow prompts, you will place the dotted line at dead ahaed and the
Select "Set"
Also, remember to TUNE VIDEO

Oct 08, 2009 | Furuno Navnet 1964CBB/NT vx2 Radar C Map...

2 Answers

Problem getting a proper fix


The antenna should be replace by raystar 125.

Regards
Michel

May 31, 2009 | Raymarine RL70CRC GPS Receiver

1 Answer

Problems talking to autopilot


I think you use the NMEA output to the autopilot .
The plotter shows you only when you have a seatalkconection with a Raymarine autopilot on you Plotter

Apr 06, 2009 | Raymarine E120 Multifunction GPS Receiver

1 Answer

Radar Displays the image upside down


If this is on the radar screen, you'll have to set your heading alignment on your radar. The radar may be 180 degrees out. if this occurs on the plotter, then if you have a heading sensor attached or an autopilot, your heading may be off.

Feb 03, 2009 | Furuno NavNet vx2 GP1720C GPS Receiver

1 Answer

Wiring of seatalk instruments


OK, you are confused. Seatalk is a bus system, using 3 wires , (power +, power-, and Data.) red, bare and yellow repectively. So Red and Bare are 12V and ground. Since the 125 shows a green light, it is getting power and outputting data. but is it seatalk?? to make a 125 Seatalk, you must hook red and green together to 12 V, so check that first. if green is grounded or not connected, that is the problem (or one of them)
Next divide system to its' simplest terms, so hook the GPS straight to the display ST60, and see if it works red to rd, yell to yell and bare to bare (sometimes black) One by one hook the others into the chain until they all work or failed device takes down Seatalk network. If you are missing 12V on a seatalk leg, check 5A fuse in course computer. If you have a pilot, you have a course computer, unless it is ST4000 wheel pilot, and then the brain is the display (course computer is built in to ST4000 display)

Sep 01, 2008 | Raymarine RL70CRC GPS Receiver

1 Answer

Rl70c raymarine depth finder problem


fish finder transducer needs to be on before you boot your system. check your hsb cables and termination

Jul 12, 2008 | Raymarine RL70CRC GPS Receiver

1 Answer

Raytheon RL70C and/or RL70CRC


Hello,

Are you still having trouble with this one?

Oct 16, 2007 | Raymarine RL70CRC GPS Receiver

1 Answer

White Screen


Defective ccd imager!! company will replace this ccd imager free of charge. Year 2002 up to 2005 released unit has a factry defect ccd imager. the company recalled these unit and replaced with a stronger version of ccd imager( they are still doing it). check it out.

Jul 26, 2006 | Fuji FinePix S5000 Digital Camera

Not finding what you are looking for?
Raymarine RL70CRC GPS Receiver Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Raymarine GPS Experts

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Steve
Steve

Level 3 Expert

691 Answers

The Knight
The Knight

Level 3 Expert

72670 Answers

Are you a Raymarine GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...