Question about Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore Elite HE4 - Smartheat Quietpak9 ERROR CODE 4E

I am getting an error code of 4E when the door is opened and the dryer will only run for 8 minutes, the only way to get it to start is to go into the diag. test mode. The whole time the dryer is running the end of cycle lights are on and there is beeping.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

Buckeyw,

Huuum,at your service!

With an error code.
This can reset the system.
First unplug the washer and wait a 5 minutes then restart it.
It's like rebooting your computer when its acting strange!
Usually it corrects some error problems.
if they are not serious, or they are a temp glitch!




How old is the appliance?

If the appliance is 10 years old or more you it may not be advisable to put good money into bad!
New appliances are so much more efficient today that they can save you a lot of money in energy!!!!
Water,Electric and detergent! And put money back in your pocket!
The new appliance will pay for itself in only a few years!


Bless You
PLEASE GIVE ME A GOOD RATING HERE AT FIXYA.COM BEFORE YOU SIGN OFF.

Thank You

Posted on Sep 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Kenmore Elite Smartheat Quiet Pak 9 won't start. Light turns on and off inside drum when door opens/closes, but no lights come on on the outside display.


My Kenmore Elite dryer keeps beeping..just going through the end of cycle alarm-high,low,off...anyone have any suggestions?

May 30, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

My Kenmore Elite Smartheat Quietpak 4 will not start. F70 code


leave door open and press the rubber botton inside, \ I just hooked up mine and it did same thing, i pushed botton light went out, so this told me the door wasnt closing correctly, you have to push hard on door first couple times. hope this helps you.
dave

Feb 09, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

My kenmore elite Smartheat quietpak9 model HE4, keep turn off after 15 to 20 minutes, it does getting hot. Could you please let me know what will be a problem. I bought it used so I am not sure how old is...


might need a clean out keeping heat inside of dryer,or you have abad motor,take the vent line off the back of dryer and run it to see if the block is in the vent line or in the dryer,also take off bottom panel,unplug dryer,take out lint filter and then remove the duct that the filter slides into,if it's blocked clean it out and you should be all set,usually the thermal fuse pops when this happens so that's why i say you could have a bad motor

Dec 15, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

New Machine Control Electronics needed?


HUH????? just change interface(buttons and board ) have never took time to ck resistance.. front interface just tells machine control what to do

Sep 03, 2008 | Kenmore Elite HE4 Electric Dryer

2 Answers

Kenmore elite dryer - smartheat - quietpak9


remove top 3 screws along rear..remove screw each side of control on top .next while pushing toward rear on top edge of control pull up and out at bottom edge where control meets lower section lift up each corner may need to remove screws holding main control in place panel has 1 02 connectors on main board there is a release clip on each connector

Jun 15, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

HE4 Kenmore Elite Dryer error code 4e


If you have ever removed the lint filter area completely via the screws that hold the plastics in so you could clean it then remove it again and insure that you plugged in the two wires that go to the strip sensor.. (moisture sensor)

May 16, 2008 | Kenmore Elite HE4 Electric Dryer

5 Answers

Kenmore Elite HE4 - Smartheat Quietpak9


Dryer heats but will not dry clothes. Uncloged linted in screen and where the tube is. Did not fix the promblem. Could it be the heating element? And if so what is the cost to replace it?

Nov 15, 2007 | Kenmore Elite HE4 Electric Dryer

1 Answer

Dryer won't start


Manual might be available on line type in your make and full model. Could well be the bulb that blew. Sounds like the door switch thou i see by other postings some times the filters can cause a similer problem
GUEST. 1. start switch is faulty...oops is it eletronic?it so disregard that. 2 drum is to tight 3 motor or switch on motor faulty
smitty123. Will drum turn by hand??? Can you hear the motor hum when you close the door???

Oct 27, 2007 | Kenmore Elite HE4 Electric Dryer

Not finding what you are looking for?
Kenmore Elite HE4 Electric Dryer Logo

Related Topics:

477 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Tim Whalen

Level 3 Expert

3069 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...