Question about Kenmore 73952 Gas Dryer

1 Answer

Won't ignite or start

Kenmore 600 Series. WhenI push the start button I can hear the electonic ignitor click but it won't start.

Posted by on

  • Anonymous Sep 27, 2008

    OLAODFKAJF D ALKA JLDA LFD FDLA JLFDJAO

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 943 Answers

HI .Thanks For The Question. The Problem you Have is With THe Coils, On The Gas Valve. Replace. THe Coils .THanks The Appliance Doc

Posted on Oct 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a kenmore 90 series elec dryer. Model # 110.64924200. When I turn it on it won't start, however I can hear it click. Like a car turning over but won't fire. Any suggestions? Already cha


the start relay in the control panel is bad,the relays coil is moving this is the click you hear,but the main contacts in the relay are bad there are 4 wires to it 2 for the start switch and 2 for the main contacts

Oct 24, 2012 | Kenmore Dryers

1 Answer

Kenmore 600 series dryer won't start. Interior light comes on


Strong possibility your dryer fuse has melted due to a lint buildup in the filter chute of your dryer. Check out my photos of a dryer tuneup I did last summer. ROPER DRYER TUNE UP

SERVICE MANUAL AND MORE PHOTOS

Jun 16, 2012 | Dryers

1 Answer

Kenmore elite gas dryer he3 model 110.95862402 won't heat


Since it is gas, you need to find out if the ignitor is coming on to ignite the gas (if you have gas getting to the burners). If you have gas, but the ignitor is not coming on, then you have to determine if the electronic contol is sending a signal for the ignitor to ignite. The most likely cause is the ignitor

Jan 16, 2012 | Kenmore Dryers

1 Answer

Drum rotates no heat,igniter dosent start


While the drum is rotating you should hear the CLICK associated with the gas valve assembly powering up to give out a blast of heat. If ya don't hear no click check the duct fuse. Right next to the control thermostat. If it is blown it kills the circuit to the gas valve assembly. If that fuse is good and the control is also good, then check the flame sensor for continuity, If it is open then the ignitor won't glow. The ignitor must glow and change in resistance then the flame sensor must open up and kill power to the ignitor so that power will be shifted to them coils on the gas valve.

Sep 03, 2011 | Maytag MDG2706A Gas Dryer

1 Answer

I have a Kenmore gas dryer Model 74812200. It is no longer heating up. When I turn it on, I hear a clicking sound for about 30 seconds then it goes off. Then about a minute later I hear the clicking sound...


You would not hear the click if the ignitor was bad. It won't click until the flame sensor get heated up by the ignitor. So that tells me the thermal fuse ain't melted. I would say them coils on the gas valve are the problem. themobilian_2943.jpg

Aug 30, 2011 | Kenmore 74812 Gas Dryer

1 Answer

My Kenmore 600 series dryer won't start when I push the start knob...I can hear a hum when the knob is pushed in but it won't start. Any suggestions?


Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor goingbad...

Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

'lll

Aug 17, 2011 | Dryers

1 Answer

When I push the start button, I can hear something running, but the dryer won't turn on.


Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor goingbad...

Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

Jul 26, 2011 | Kenmore 600 7965 Dryer

1 Answer

Kenmore 70 series gas dryer - does not start when pushing the start button


Hi, If you have a gas dryer2_bing.gif.
The most common problem with a gas and no heat is the ignitor going bad...

Here is a tip that I wrote about that problem...

Gas Dryer2_bing.gif not Working Gas Dryer2_bing.gif Not Heating
http://www.fixya.com/support/r4398592-gas_dryer_not_working_gas_dryer_not

If your dryer2_bing.gif is electric2_bing.gif..
There could be a number of different problems...
Check out this tip that I wrote about this problem...

Dryer2_bing.gif Troubleshooting2_bing.gif Electric2_bing.gif Dryer2_bing.gif won t Heat
http://www.fixya.com/support/r3866345-dryer_troubleshooting_electric_dryer_won


heatman101

May 19, 2010 | Kenmore 77632 Gas Dryer

1 Answer

Need help with gas dryer Kenmore 90 series serial


Check the lint caught in the exhaust vents. If it is clear replace the spark ignitor if no click is hear upon starting up

May 14, 2010 | Kenmore 73952 Gas Dryer

Not finding what you are looking for?
Kenmore 73952 Gas Dryer Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...